11-06-07 Item 13 Plan (8)►a
C
■i
E
GENERAL CONDITIONS
1. THESE SPECIFICATIONS AND CONSTRUCTION DRAWINGS ACCOMPANYING THEM
DESCRIBE THE WORK TO BE DONE AND THE MATERIALS TO BE FURNISHED FOR
THE CONSTRUCTION OF THE T- MOBILE FACILITY.
2. BEFORE BEGINNING WORK AT THE SITE INSPECT THE EXISTING BUILDING AND
DETERMINE THE EXTENT OF EXISTING FINISHES SPECIALTIES, EQUIPMENT AND
OTHER ITEMS THAT MUST BE REMOVED AND REINSTALLED IN ORDER TO PERFORM
THE WORK UNDER THIS CONTRACT.
3. THE ENGINEERING DRAWINGS SHOW PRINCIPAL AREAS WHERE WORK MUST BE
ACCOMPLISHED UNDER THIS CONTRACT. INCIDENTAL WORK MAY ALSO BE
NECESSARY IN AREAS NOT SHOWN ON THE ENGINEERING DRAWINGS DUE TO
CHANGES AFFECTING EXISTING ELECTRICAL OR OTHER SYSTEMS. SUCH
INCIDENTAL WORK IS ALSO A PART OF THIS CONTRACT. INSPECT THOSE AREAS
AND ASCERTAIN WHAT IS NEEDED TO DO THAT WORK IN ACCORDANCE WITH THE
CONTRACT REQUIREMENTS AT NO ADDITIONAL COST.
4. SHOULD ANY ERROR OR INCONSISTENCY APPEAR IN THE DRAWINGS OR
SPECIFICATIONS, THE CONTRACTOR BEFORE PROCEEDING WITH THE WORK MUST
MAKE MENTION OF THE SAME TO AW SOLUTIONS AND OWNER FOR PROPER
ADJUSTMENT AND IN NO CASE PROCEED WITH THE WORK IN
UNCERTAINTY OR WITH INSUFFICIENT DRAWINGS.
5. THE INTENTION OF THE DOCUMENTS IS TO INCLUDE ALL LABOR AND MATERIALS
REASONABLY NECESSARY FOR THE PROPER EXECUTION AND COMPLETION OF THE
WORK AS STIPULATED IN THE CONTRACT.
6. THE CONTRACTOR AND EACH SUBCONTRACTOR SHALL BE RESPONSIBLE FOR
VERIFICATION OF ALL MEASUREMENTS AT THE SITE BEFORE ORDERING ANY
MATERIALS OR DOING ANY WORK. NO EXTRA CHARGE OR COMPENSATION SHALL BE
ALLOWED DUE TO DIFFERENCE BETWEEN ACTUAL DIMENSIONS AND DIMENSIONS
INDICATED ON THE CONSTRUCTION DRAWINGS. ANY SUCH DISCREPANCY IN
DIMENSIONS WHICH MAY BE FOUND SHALL BE SUBMITTED TO AW SOLUTIONS
AND THE T- MOBILE REPRESENTATIVE FOR CONSIDERATION BEFORE THE
CONTRACTOR PROCEEDS WITH THE WORK IN THE AFFECTED AREAS.
7. THE PURPOSE OF THESE SPECIFICATIONS IS TO INTERPRET THE INTENT OF THE
DRAWINGS AND TO DESIGNATE THE METHOD OF THE PROCEDURE, TYPE AND
QUALITY OF MATERIALS REQUIRED TO COMPLETE THE WORK.
8. TRADE, PRODUCT NAMES OR MANUFACTURERS NAMES OR CATALOG NUMBERS AND
INDICATIONS OF PRODUCT TYPES SUCH AS (DUCT SEAL) SHOWN ON THE
DRAWINGS OF EXISTING PRODUCTS ARE BELIEVED TO BE ACCURATE. IF THEY
ARE DISCOVERED TO BE INACCURATE, NOTIFY AW SOLUTIONS
IMMEDIATELY AND DO NOT PROCEED WITHOUT INSTRUCTIONS.
9. DIMENSIONS TO EXISTING SURFACE ARE TO FINISHED FACE.
10. DO NOT DRILL OR CUT EXISTING FLOOR JOISTS, BEAMS COLUMNS OR OTHER
STRUCTURAL ELEMENTS UNLESS SPECIFICALLY INDICATED. DRILL SLABS WHERE
APPROVED. CORE DRILL CIRCULAR OPENINGS THROUGH CONCRETE SLAB. LINE
DRILL FOR RECTANGULAR OPENINGS. MAKE OPENINGS OF PROPER SIZE FOR
CONDUIT, DUCTS, PIPES AND OTHER ITEMS PASSING THROUGH OPENINGS.
MAKE ALL NEW HOLES ON OPENINGS WEATHER TIGHT OR FIRE
SAFE AS REQUIRED BY LOCAL BUILDING CODES & ORDINANCES.
11. PREPARE, SUBMIT AND RECEIVE APPROVAL OF SLEEVES AND OPENING DRAWINGS
BEFORE LOCATING SLEEVES AND OPENINGS IN NEW CONSTRUCTION AND BEFORE
DRILLING EXISTING STRUCTURE. SHOW EACH OPENING AND SLEEVE IN THE
ENTIRE PROJECT.
12. REPAIR, PATCH, FINISH AND /OR REFINISH AS APPLICABLE TO MATCH ADJACENT
EXISTING FINISHES THOSE EXISTING SURFACES DAMAGED OR NEW PROPOSED
SURFACES DURING PERFORMANCE OF THE WORK UNDER THIS CONTRACT.
13. WHERE CUTTING OF EXISTING SURFACES OR REMOVAL OF EXISTING FINISHES IS INDICATED,
REQUIRED TO PERFORM THE WORK UNDER THIS CONTRACT AND A NEW FINISH IS
NOT INDICATED, FILL RESULTING OPENINGS AND PATCH THE SURFACE AFTER
DOING THE WORK AND FINISH TO MATCH ADJACENT EXISTING SURFACES.
14. EXCEPT IN SPACE WHERE NO WORK UNDER THIS CONTRACT IS REQUIRED,
ENCLOSE EXISTING AND NEW CONDUITS, DUCTS, PIPES AND SIMILAR ITEMS IN FURRING
WHERE SUCH ITEMS PASS THROUGH FINISHED SPACES WHETHER OR NOT FURRING
IS INDICATED.
15. WHERE CONDUITS, DUCTS, PIPES AND SIMILAR ITEMS ARE SHOWN TO BE
INSTALLED IN EXISTING WALLS OR PARTITIONS NEATLY CHASE THE WALLS
OR PARTITIONS. INSTALL THE ITEMS AND PATCH THE WALLS OR PARTITIONS
TO MAKE THE INSTALLATION NOT DISCERNIBLE IN THE FINISHED WORK.
16. SEAL WATER TIGHT AND PROTECT WITH FIRE SAFING MATERIALS FOR NEW SLEEVES
AND OPENINGS THROUGH ROOFS, FLOORS AND IN VERTICAL CHASES AS
REQUIRED BY CODE AND INDUSTRY STANDARDS.
17. WHERE A NEW CUTTING IS NOT SCHEDULED, INSTALL NEW CONDUITS AND PIPES
IN EVERY CASE, AND NEW DUCT WHERE POSSIBLE ABOVE EXISTING CEILING.
REMOVE EXISTING CEILING AS NECESSARY. AFTER INSTALLATION OF CONCEALED
WORK, REINSTALL REMOVED CEILING AND PATCH AND REFINISH TO MATCH
ADJACENT UNREMOVED CEILINGS.
18. NOISE AND EXISTING BUILDING STRUCTURE VIBRATION GENERATED BY
CONSTRUCTION PROCEDURES, EQUIPMENT, TOOL AND OPERATIONS ARE TO BE KEPT
TO A PRACTICABLE MINIMUM. WHERE USE OF HIGH NOISE LEVEL EQUIPMENT IS
UNAVOIDABLE, AND CAN BE HEARD, CONFINE TO HOURS BEFORE 10 A.M. AND AFTER
5 P.M. MONDAY THROUGH FRIDAY OR AS AGREED TO BY BUILDING OWNER.
19. DAY -BY -DAY CLEANUP: REMOVE STAINING OR REACTIVE MATERIALS FROM NEW AND
EXISTING SURFACES IMMEDIATELY. REMOVE HAZARDOUS ACCUMULATIONS OF
DEBRIS PROMPTLY, AT LEAST DAILY. CONFINE DUST PRODUCING OPERATIONS
DURING PAINTING AND FINISHING. THERE SHOULD BE NO OVER SPRAYING PAINT
IN PARKING AREA. VACUUM IMMEDIATELY AFTER COMPLETION.
20. CONSTRUCTION SITE ACCESS: USE MOST DIRECT ROUTE FROM PUBLIC STREET AS
AGREED TO BY BUILDING OWNER. FOR ACCESS TO EXISTING BUILDING INTERIOR USE
LOADING DOCK AS AGREED TO BY BUILDING OWNER.
1
2
R
21. FOR TEMPORARY USE OF EXISTING ELEVATOR, SUBMIT FOR APPROVAL A LIST OF
THE PROCEDURES PROPOSED TO PROTECT EXISTING ELEVATOR FROM HARM DURING
USE. PROTECT CAB, ENTRANCES AND ADJACENT SURFACES FROM DAMAGE. DO
NOT OVERLOAD ELEVATOR. MAINTAIN ELEVATOR DURING USE AND RETURN
TO ORIGINAL CONDITION AT COMPLETION.
22. CONSTRUCTION PERSONNEL MAY USE EXISTING STAIRS AND CORRIDORS FOR
CONSTRUCTION PURPOSES. PROTECT STAIR AND ACCESS WAYS AND RETURN TO
ORIGINAL CONDITION AT COMPLETION. COORDINATE WITH BUILDING OWNER FOR
USE OF WASHROOM FACILITY.
23. PROVIDE PROPER TEMPORARY PROTECTION OF HIGH TRAFFIC AREAS.
24. AT PROJECT COMPLETION, REMOVE TEMPORARY SERVICES, CONSTRUCTION
EQUIPMENT, TOOLS AND FACILITIES, MOCKUPS, TEMPORARY STRUCTURES.
SURPLUS MATERIALS, DEBRIS, AND RUBBISH FROM BUILDING OWNERS PROPERTY.
PUT SITE IN NEAT, ORDERLY CONDITION, READY FOR USE. LEAVE ROOF AREAS,
PIPE SPACES AND OTHER SPACES CLEAN AND FREE FROM DEBRIS ON A DAILY BASIS.
25. RELATED DOCUMENTS AND COORDINATION:
GENERAL CARPENTRY, ELECTRICAL, AND ANTENNA DRAWINGS ARE INTERRELATED. IN
PERFORMANCE OF THE WORK, EACH CONTRACTOR MUST REFER TO ALL DRAWINGS.
ALL COORDINATION TO BE THE RESPONSIBILITY OF THE GENERAL CONTRACTOR.
26. SHOP DRAWINGS (ARE REQUIRED):
A. CONTRACTORS TO SUBMIT SHOP DRAWINGS AS REQUIRED AND LISTED IN THESE
SPECIFICATIONS THROUGH THE GENERAL CONTRACTOR TO AW SOLUTIONS
FOR APPROVAL.
B. ALL SHOP DRAWINGS TO BE REVIEWED, CHECKED AND CORRECTED BY GENERAL CONTRACTOR
PRIOR TO SUBMITTAL TO AW SOLUTIONS. AW SOLUTIONS WILL RETURN SHOP
DRAWINGS TO GENERAL CONTRACTOR WITHIN 3 WORKING DAYS
OF RECEIPT. DO NOT PERFORM WORK BEFORE APPROVAL OF SHOP DRAWINGS.
27. THE SUBCONTRACTOR MUST VERIFY ALL DIMENSIONS, CONDITIONS AND ELEVATIONS BEFORE
STARTING WORK. ALL DISCREPANCIES SHALL BE CALLED TO THE ATTENTION OF THE
ENGINEER AND SHALL BE RESOLVED BEFORE PROCEEDING WITH THE WORK. ALL WORK
SHALL BE PERFORMED IN A WORKMANLIKE MANNER IN ACCORDANCE WITH ACCEPTED
CONSTRUCTION PRACTICES.
28. IT IS THE INTENTION OF THESE DRAWINGS TO SHOW THE COMPLETED INSTALLATION. THE
CONTRACTOR SHALL BE RESPONSIBLE FOR ALL TEMPORARY BRACING, SHORING,
TIES, FORMWORK, ETC. IN ACCORDANCE WITH ALL NATIONAL, STATE, AND LOCAL
ORDINANCES, TO SAFELY EXECUTE ALL WORK AND SHALL BE RESPONSIBLE FOR SAME.
ALL WORK SHALL BE IN ACCORDANCE WITH LOCAL CODES.
29. SUBCONTRACTOR WILL BE REQUIRED TO ASSUME SOLE AND COMPLETE RESPONSIBILITY
FOR JOB SITE CONDITIONS DURING THE COURSE OF CONSTRUCTION OF THE PROJECT,
INCLUDING SAFETY OF ALL PERSONS AND PROPERTY THIS REQUIREMENT APPLY
CONTINUOUSLY AND NOT BE LIMITED TO NORMAL WORKING HOURS.
30. ALL WORK SHALL COMPLY WITH OSHA AND STATE SAFETY REQUIREMENTS.
31. CORE LOCATIONS IF REQUIRED SHALL BE CHOSEN SO AS TO AVOID CUTTING ANY REINFORCING
BARS. FIRESTOP FLOOR OR WALL PENETRATION WITH TWO HOUR RATED SEALANT TO MEET
UL CAJ5045. PROVIDE WEATHERPROOFING OF ANY ROOF PENETRATIONS
32. ALL WORK PERFORMED & MATERIAL USED SHALL BE IN ACCORDANCE WITH THE PROVISIONS OF
THE LATEST EDITION OF THE FLORIDA BUILDING CODE.
4
5
I
I
ABBREVIATIONS
&
LEGEND
ACLC
EXISTING PROPERTY LINE
ATS
PROPOSED LEASE LINE
X
EXISTING FENCE
C
EXISTING CONTOUR
COAX
EXISTING EDGE OF FENCE
❑H
EXISTING OVERHEAD UTILITY LINE
O
IRON FENCE
Q�
IRON ROD SET 5/8"
ro,
UTILITY POLE
C
GUY ANCHOR
®
WATER METER
E. S.
EXISTING TREE
FT.
BENCH MARK
H
SANITARY SEWER MANHOLE
IN.
FLOW DIRECTION
®
SHUT OFF VALVE
®
FIRE HYDRANT
ABBREVIATIONS
&
AND
ACLC
ALTERNATING CURRENT LOAD CENTER
ATS
AUTOMATIC TRANSFER SWITCH
DIA
DIAMETER
C
CENTER LINE
COAX
COAXIAL CABLE
CONC.
CONCRETE
CONT.
CONTINUOUS
C. J.
CONTROL JOINT
DIA.
DIAMETER
DWG
DRAWING
EL.
ELEVATION
E. S.
EACH SIDE
FT.
FEET
HORIZ.
HORIZONTAL
IN.
INCH
MAX
MAXIMUM
MFR.
MANUFACTURER
MIN
MINIMUM
MPH
MILES PER HOUR
R
PLATE
REQ'D
REQUIRED
SIM.
SIMILAR
STD.
STANDARD
STL.
STEEL
TYP.
TYPICAL
U.N.O.
UNLESS NOTED OTHERWISE
W/
WITH
W. G.
WAVEGUIDE
I
i
APPLICANT /OWNER:
a LN u sb
Get more from hfd
T- Mobile USA, Inc
8100 SW 10th Street
Plantation, FL 33324
Phone: (954) 693 -7172
Fax (954) 693 -7240
PREPARED BY:
ff�s�m A "00
Wsolutsions
I n c o r p o r a t ad
300 CROWN
OAK CENTRE DRIVE
LONGWOOD, FL 32750
TELL
407.260.0231
FAXL
407.260.0749
FL.
COA# 26983
IREVIREV ISIONS
DATE I DESCRIPTION
1 1 9/24/071 REVISED SITE NAME
0
1 6/7/06
ISSUED
FOR
ZONING
B
6/5/06
REVISED
PER
ZONINIG
A
4/13/06
ISSUED
FOR
REVIEW
SEAL
EMMANUEL POULIN
FL. P.E. #54073
IT IS A VIOLATION CF LAW FCF' AIli PEP1,N] UIILE`_S THE, ARE
ACTfTIG LI -1EEP THE DIPE(-TI011 )F 4 Lk EASED F'Pt�FE`_SIC�1lAL
EPIGINEEP TO ALTER THIS D CIJt.lEilf IJIILE-'S E•PLII.ITLi AGREED
TO Et Ill `APITH:(:, A1V �' U.1110I11 DGCL ALL
LIAEILIT� A'= Sir ".IATED 141711 fllE PEIP-E, AL1FF'AT =� t] �,P
G "ODIFICATIC�II CF IIIL _ flTEtIT'- HEF'E'11.
NOT VALID WITHOUT SIGNATURE & SEAL
PROJECT LOCATION:
SITE #M D 1277
GULLIVER SITE
8512 SW 57TH AVENUE
SOUTH MIAMI, FL 33156
ROOFTOP
DRAWN BY: SB
CHECKED BY: SE
DATE: 05/16/06
JOB NO. : 120.005
SITE NO. : MD1277
DRAWING DESCRIPTION:
GENERAL NOTES
DRAWING NUMBER:
Z2