01-0102-009 NUM DATE REMARKS
GENERAL NOTES 18. CLEAN UP: FINISH HARDWARE NOTES: ELECTRICAL NOTES:
THE CONTRACTOR SHALL BE RESPONSIBLE FOR -THE_ REMOVA-_ OF ALL TRASH AND DEBRIS '
1• EXAMINATION OF THE CONTRACT DOCUMENTS AND SITE: FROM THE JOB SITE. _ = - -
1. INSTALLATION: 1• GENERAL
EACH CONTRACTOR FOR THIS PROJECT SHALL STUDY AND FAMILIARIZE HIMSELF WITH THE 19. GUARANTEE: �� DO NOT SCALE ELECTRICAL DRAWINGS. REFER TO THE ARCHITECTURAL PLANS AND ELEVATIONS
SITE AND WITH ALL OF THE DRAWINGS FOR ALL TRADES AND PARTS OF THE WORK. SHOULD __ THE CONTRACTOR SHALL RECEIVE,- STORE, B` RESPONSIBLE F.... AND INSTALL ALL SPECIFIED FOR THE EXACT LOCATION OF ALL EQUIPMENT AND CONFIRM WITH THE OWNERS REPRESENTATIVE.
ANY CONTRACTOR HAVE THE OPINION THAT THERE EXIST IN THE ARCHITECTURAL DRAWINGS HARDWARE. HARDWARE SHALL BE- INSTALLED IN ACCORDANCE WITH THE MANUFACTURER'S
THE CONTRACTOR SHALL BE RES�10&SIBLE FOR 1 HE SATISFACTORY OPERATION OF ALL
ANY ERRORS OR DISCREPANCIES, OR THAT CONDITIONS OF THE WORK OF ANY OTHER INSTRUCTIONS, ACCURATELY FITTED, SECURELY APPLIED AND PROPERLY ADJUSTED. LOST, IT IS NOT THE INTENT OF THESE PLANS TO SHOW EVERY MINOR DETAIL OF CONSTRUCTION. THE
CORRELATED PARTS OF THE BUILDING; FORA PERIOD_ Or ONE YEAR AFTER THE DATE OF
CONTRACTOR IS SUCH THAT WILL PREVENT HIM FROM COMPLETING HIS WORK IN A COMPETENT STOLEN OR DAMAGED HARDWARE MUST BE REPLACED. HARDWARE SHALL BE INSTALLED SO CONTRACTOR IS EXPECTED TO FURNISH AND INSTALL ALL ITEMS NECESSARY FOR EQUIPMENT TO
ACCEPTANCE OF THE OWNER, AND"SHALL MAKE ALTERATIONS, REPAIRS, OR ADJUSTMENTS,
MANNER, HE SHALL NOTIFY THE OWNER OF SUCH BEFORE PROCEEDING WITH THE WORK. AS TO AVOID DAMAGE TO EXISTING WORK. ALL FINISHES SHALL BE PROTECTED DURING AND TO BE PLACED IN PROPER WORKING ORDER. FURNISH AND INSTALL ALL FIXTURES AS CALLED FOR ON
NECESSARY TO CORRECT PROBLEMS CAUSED BY THE USE OF FAULTY MATERIALS OR AFTER INSTALLATION. y
THE CONTRACTOR SHALL HAVE AT THE BUILDING SITE, FROM START TO FINISH OF CONSTRUCTION WORKMANSHIP BY HIM OR ANY OF HIS SUB-CONTRACTORS. THE PLANS OR AS SELECTED BY OTHERS.
A RESPONSIBLE FOREMAN. IN ADDITION, THE CONTRACTOR SHALL GIVE HIS PERSONAL SUPER- 2. PROTECTION: LOAD DATA IS BASED ON INFORMATION GIVEN TO THE ENGINEER AT THE TIME OF THE DESIGN. ALL '
VISION TO THE WORK. THE FOREMAN SHALL BE ON DUTY DURING ALL WORK HOURS. ANY SITE NOTES: EQUIPMENT AND PANEL SIZES SHALL BE VERIFIED PRIOR TO ORDERING.
INSTRUCTIONS OR NOTICES GIVEN TO HIM SHALL HAVE THE SAME IMPORTANCE AS IF GIVEN ALL ITEMS OF HARDWARE SHALL BE INDIVIDUALLY WRAPPED WITH PROTECTIVE PAPER AND
TO THE CONTRACTOR IN PERSON. STORED BY THE GENERAL CONTRACTOR ON THE JOB UNTIL THE TIME OF INSTALLATION. AFTER
1. VERIFY EXISTING CONDITIONS: FINAL INSTALLATION, CHECH ADJUST OR REPLACE DEFECTIVE HARDWARE. PROTECT ALL CIRCUITS SHOWN ON THE PLANS ARE TO DETERMINE THE LOAD DATA AND PANEL SIZE. THE CONTRACTOR
SHALL PROVIDE CIRCUIT ROUTING TO SUITE THE JOB CONDITIONS.
THE CONTRACTOR SHALL BE RESPONSIBLE FOR PROVIDING AND MAINTAINING TEMPORARY FINISHES AS REQUIRED.
PROVISIONS SUCH AS TOILETS, WATER SUPPLY, LIGHT AND POWER AS WELL AS ANY OTHER THE CONTRACTOR PRIOR TO COMMENCEMENT OF WORK SHALL VISIT THE SITE AND VERIFY IF PAINTING IS TO BE DONE AFTER INSTALLATION OF HARDWARE, REMOVE AND REINSTALL '
DEEMED NECESSARY FOR THE COMPLETING OF THE BUILDING. THE LOCATION OF ALL UTILITIES AND DETERMINE THEIR CAPACITIES. HARDWARE WHEN THE SURFACES ARE COMPLETELY DRY. 2. CODES .
Copywrite 2001 Gene Farmer and Associates
ANY ITEM OF WORK NECESSARY TO THE PROPER COMPLETION OF CONSTRUCTION WHICH IS PROTECT AND MAINTAIN CONDUITS, DRAINS, PIPES, SEWERS, AND WIRES WHICH ARE TO All drawings and ideas shown on this drawing
NOT SPECIFICALLY COVERED IN THESES DOCUMENTS SHALL BE PERFORMED IN A MATTER REMAIN ON PROPERTY OR WHICH WILL REMAIN UNTIL NEW INSTALLATIONS ARE COMPLETE. 3' ALL WORK SHALL BE DONE IN ACCORDANCE WITH THE NEC. . . AND SHALL COMPLY WITH ALL LOCAL are the property of Gene Farmer. They may
RULES AND ORDINANCES. not be used in whole or in part without the
DEEMED GOOD PRACTICE IN THE TRADE INVOLVED.
COORDINATE ALL TIE IN AND SERVICE TO UTILITIES WITH THE UTILITY COMPANIES. PROVIDE 2 MASTER KEYS FOR EACH LOCKSET. THE TWO MASTER KEYS ARE TO BE GIVEN written permission of Gene Farmer.
TO THE OWNER AT THE COMPLETION OF THE WORK. ALL LOCKS AND DEADBOLTS SHALL BE ELECTRICAL INSTALLATION SHALL MEET ALL STANDARDS AND REQUIREMENTS OF THE LOCAL ELECTRICITY
2. VERIFICATIONS OF EXISTING CONDITIONS: 2. PROTECTION OF ADJACENT PROPERTIES: KEYED ALIKE UNLESS SPECIFIED OTHERWISE. UTILITY AND TELEPHONE COMPANIES.
EACH CONTRACTOR SHALL DETERMINE AND VERIFY ALL DIMENSIONS AND CONDITIONS AT THE 4. ACCEPTANCE: THE ELECTRICAL SYSTEM SHALL BE COMPLETELY AND EFFECTIVELY GROUNDED AS REQUIRED BY THE
BUILDING SITE AND BE RESPONSIBLE FOR SAME BEFORE COMMENCING THE WORK. DISCRE- TAKE ALL NECESSARY PRECAUTIONS TO PROTECT ADJOINING PROPERTY FROM EXCESSIVE DRAINAGE, DEBRIS, AND ASSUME FULL RESPONSIBILITY FOR DAMAGES RESULTING FROM E THE CONTRACTOR IS RESPONSIBLE FOR THE CONDITION AND OPERATION OF ALL HARDAWARE LATEST EDITION OF THE NATIONAL ELECTRIC CODE.
G UNTIL THE COMPLETION OF THE WORK AND ACCEPTANCE BY THE OWNER.
PENCIES SHALL BE REPORTED TO THE ARCHITECT AND/OR ENGINEER AND SHALL BE RESOLVED NEGLIGENCE. ALL WORK SHALL PERFORMED BY A LICENSED ELECTRICAL CONTRACTOR AND IN A FIRST CLASS
BEFORE RESUMING THE WORK. DIMENSIONS SHALL BE READ AND NEVER SCALED OR ESTIMATED WORKMAN LIKE MANNER. THE COMPLETED SYSTEM SHALL BE FULLY OPERATIVE.
FROM THE ARCHITECTURAL DRAWINGS.
SOIL BEARING CAPACITIES HAVE BEEN ASSUMED AT 2,000 P.S.I. UNLESS OTHERWISE CERTIFIED 3. FILL: INTRUSION AND BURGLARY SECURITY NOTES: ALL REQUIRED INSURANCE SHALL BE PROVIDED FOR PROTECTION AGAINST PUBLIC LIABILITY AND
HEREIN. SHOULD CONDITIONS OR MATERIALS BE ENCOUNTERED THAT REDUCE THE BEARING PROVIDE AND PLACE ANY ADDITIONAL FILL NEEDED TO BRING EXISTING GRADES TO NEW PROPERTY DAMAGE FOR THE DURATION OF THE WORK.
CAPACITIES OF THE SOIL THE CONTRACTOR SHALL NOTIFY THE ARCHITECT OF THESE GRADES INDICATED ON THE DRAWINGS. DISPOSE OF ANY EXCESS EARTH ON PROPERTY AS 1. DOOR LOCKS ON ALL EXTERIOR DOORS SHALL BE CAPABLE OF RESISTING A FORCE OF 300 THE CONTRACTOR SHALL PAY FOR ALL PERMITS, FEES, INSPECTIONS, AND TESTING.
CONDITIONS PRIOR TO THE EXECUTION OF THE WORK. NECESSARY. LBS. APPLIED IN ANY MOVABLE DIRECTION AND IN ACCORDANCE WITH RESISTANCE STAND-
ARDS SET FORTH IN METRO CODE 8C. ALL SINGLE EXTERIOR SWING DOORS SHALL HAVE A ALL WORK SHALL BE COORDINATED WITH THE OTHER TRADES TO AVOID INTERFERENCE WITH THE g
LOCK TO BE KEY OPERATED FROM THE EXTERIOR WITH A MINIMUM OF 6000 POSSIBLE KEY PROGRESS OF THE WORK.
3. CODE COMPLIANCE 4. LANDSCAPING: CHANGES OR AN AUXILLIARY LOCKING SINGLE DEADBOLT WITH HARDENED BOLT INSERTS.
EACH CONTRACTOR SHALL COMPLY WITH THE REQUIREMENTS OF THE,SOUTH FLORIDA BUILDING.,. COMPLETELY REMOVE ALL TREES, SHRUBS, STUMPS, SOD, AND ALL OTHER ORGANIC DEBRIS a�
CODE AND WITH ALL OTHER CODES AND GOVERNMENTAL AGENCIES HAVING'JURISDICTION_OVER FROM AREAS TO BE COVERED BY THE BUILDING AND PAVED AREAS. 2. THE ACTIVE LEAF OF PAIRS OF EXTERIOR SWING DOORS SHALL HAVE THE SAME LOCKS AS 3. MATERIALS
,HIS PORTION OF THE WORK. EACH CONTRACTOR SHALL BE RESPONSIBLE FOR CONSTRUCTION REQUIRED FOR SINGLE EXTERIOR SWING DOORS. THE INACTIVE LEAF OF THESE DOORS SHALL
MEANS, METHODS, TECHNIQUES, SEQUENCES, AND PROCEDURES, AND FOR SAFETY PRECAUTIONS HAVE MULTIPLE POINT LOCKS WITH 5/8" MINIMUM THROW BOLTS WITH HARDENED INSERTS. ALL MATERIALS SHALL BE NEW AND SHALL BEAR UNDERWRITERS LABELS WHERE APPLICABLE. MINIMUM
CONNECTIONS WITH HIS PORTION OF THE WORK. 5. PAVING: WIRE SIZE SHALL BE #12 AWG UNLESS OTHERWISE NOTED. ALL CONDUCTORS SHALL BE COPPER WITH �J1
3. SLIDING GLASS RS DOO SHALL BE PROVIDED WITH SLIDING DOOR DEADBOLTS OR A BOLT OR TW INSULATION FOR #8 AND SMALLER. CONDUCTORS LARGER THAN #8 SHALL HAVE TYPE THW INSUL- k
ALL ASPHALT PAVING SHALL BE 1" HOT PLANT MIX OVER 6" UNIFORMLY GRADED AND PIN NOT REMOVABLE OR OPERABLE FORM THE EXTERIOR AT THE JAMB. HEAD, SILL OR AT ATION. ALL CONDUCTORS #10 AND SMALLER MAY BE SOLID AND THOSE #8 AND LARGER SHALL BE P�
4, PERMITS_ FEES, AND TAXES: COMPACTED CRUSHED STONE BASE. AFTER PROPER CURING ENTIRE SURFACE SHALL BE MEETING MULLIONS. THESE DOORS SHALL BE REINFORCED IN THE STRIKE AND LOCK AREA STRANDED. F�1
FULLY SEALED. TO MAINTAIN BOLT STRENGTH EFFECTIVENESS, IF NECESSARY, AND SUCH DOORS SHALL HAVE
THE CONTRACTOR SHALL OBTAIN AND PAY FOR ALL PERMITS FEES LICENSES AND DEPOSITS DISCONNECT SWITCHES SHALL BE HORSEPOWER RATED HEAVY-DUTY QUICK-MATE QUICK-BREAK AND P4 O � Fes+
AND BE LIABLE FOR ALL STATE AND FEDERAL TAXES, AND ALL OBLIGATIONS UNDER THE 6. UNDERGROUND UTILITIES: NO SCREWS REMOVABLE FROM THE EXTERIOR WHICH WOULD FACILITATE READY ENTRY FROM IN A N.E.M.A. ENCLOSURE.
THE OUTSIDE.
- FEDERAL SECURITY ACT. UPON COMPLETION OF THE PROJECT, THE CONTRACTOR SHALL ALL RACEWAY OR PIPES PLACED IN OR THRU ANY CONCRETE SLAB SHALL BE SPACED A MINIMUM OF
OBTAIN CERTIFICATES OF COMPLIANCE, APPROVAL OF ACCEPTANCE, FROM ALL AUTHORITIES THE CONTRACTOR SHALL CONTACT U.N.C.L.E. TO ASCERTAIN THE EXACT LOCATION OF ALL 4, HINGES ON ALL OUT-SWINGING EXTERIOR DOORS SHALL HAVE NON REMOVABLE PINS. THREE DIAMETERS OF THE LARGEST CONDUIT OR PIPE FROM ANY OTHER SERVICE.
HAVING JURISDICTION OVER THE WORK AND DELIVER THESE CERTIFICATES TO THE OWNER UNDERGROUND UTILITIES BEFORE EXCAVATING. DO NOT GO BY ORIGINAL CONSTRUCTION
ALONG WITH OFFICIAL RECEIPTS FOR THE SAME. DRAWINGS OR AS BUILT. THE CONTRACTOR SHALL COORDINATE WORK OF ALL TRADES IN
THIS AREA AND INFORM ALL SUB CONTRACTORS OF UNDERGROUND UTILITY LOCATIONS. 5. JAMBS OF ALL EXTERIOR OFFSET TYPE IN-SWINGING DOORS SHALL BE RABSETTED OR OF 4. GUARANTEE
_ SIMILAR FABRICATION, TO PREVENT DEFEATING THE PURPOSE OF THE STRIKE AND THE INTE-
5. PERFORMANCE OF THE WORKS
GRITY OF LOCKS AND LATCHES. THE CONTRACTOR SHALL GUARANTEE ALL MATERIALS AND WORKMANSHIP TO BE FREE FROM DEFECTS
NO SUB CONTRACTOR SHALL BEGIN HIS WORK UNLESS THE PREVIOUS TRADE, UPON WHOM FINISH NOTES: 6. SINGLE SWINGING EXTERIOR WOOD DOORS SHALL BE SOLID CORE IF LESS THAN 1-3/8" FOR A PERIOD OF ONE YEAR FROM THE DATE OF ACCEPTANCE BY THE OWNER.
HE IS DEPENDENT, HAS PERFORMED THEIR WORK SATISFACTORILY ACCORDING TO THE PLANS THICK. CORRECTION OF DEFECTS SHALL BE COMPLETED WITHOUT ADDITIONAL CHARGE AND INCLUDE ANY
AND SPECIFICATIONS. ONCE THE CONTRACTOR HAS STARTED HIS WORK, HE ASSUMES FULL REPLACEMENT OR REPAIR OF ANY ADDITIONAL CHARGE AND INCLUDE REPLACEMENT OR REPAIR OF ANY
RESPONSIBILITY FOR THAT WORK, BOTH THE MATERIALS AND LABOR PERFORMED. ALL SUB 1. THE CONTRACTOR SHALL BE RESPONSIBLE FOR PROVIDING AND INSTALLING ALL FINISHES AS 7. GLASS AND EXTERIOR DOORS SHALL COMPLY WITH THE AMERICAN NATIONAL STANDARDS OTHER PHASE OF INSTALLATION WHICH MAY HAVE BEEN DAMAGED.
CONTRACTORS ARE RESPONSIBLE FOR REMOVING DEBRIS, RESULTING FROM THEIR WORK CALLED FOR IN THE DRAWINGS AND SPECIFICATIONS. INSTITUTE STANDARD 297.1. FRONT MAIN ENTRANCE DOORS SHALL BE PROVIDED WITH A
FROM THE PREMISES. 2. CERAMIC TILE: DOOR SCOPE OF VISION PANELS.
6. CLEANUP: ALL CERAMIC TILE, GROUT, MORTAR AND ACCESSORIES, SHALL BE SUPPLIED AND INSTALLED 8. VISION PANELS D EXTERIOR
ICE ER 0 I R
DOORS OTHER THAN GLAZING WITHIN 40" OF THE INSIDE LOCK- ate
BY THE CONTRACTOR UNLESS NOTED OTHERWISE. ING ACTIVATING DEVICE OF LOOSE AND SWINGING DOORS SHALL COMPLY WITH AMERICAN
IN ADDITION TO THE REMOVAL OF ALL CONSTRUCTION DEBRIS FROM THE PREMISES, IT IS THE NATIONAL STANDARDS INSTITUTE'S - STANDARD 297.1.
FINAL RESPONSIBILITY OF THE CONTRACTOR TO REMOVE ALL SMUDGES, SPOTS OF PLASTER, THE TILE CONTRACTOR MUST INSPECT ALL SURFACES CAREFULLY PRIOR TO THE INSTALLATION
PUTTY, CAULKING COMPOUND, ADHESIVE, PAINT AND PENCIL DRAWINGS, TAGS AND DESTINATION OF MATERIALS. HE SHALL REPORT TO THE ARCHITECT AND GENERAL CONTRACTOR ANY 9. SLIDING GLASS DOORS AND WINDOWS SHALL BE INSTALLED AND CONSTRUCTED SO THAT NO
LABELS NOT CALLED FOR AS BEING PERMANENT. THE CONTRACTOR SHALL ALSO CLEAN EACH PANEL CAN BE LIFTED FORM THE TRACKS WHEN IN THE LOCKED POSITION AND SO AS TO
SURFACE NOT SUITABLE FOR THE INSTALLATION OF HIS WORK. IT IS THE RESPONSIBILITY t
AREA SEPARATELY, INCLUDING THE WASHING OF ALL WINDOWS AND VACUUMING OR WAXING OF THE GENERAL CONTRACTO TO CORRECT ALL SURFACES. ALL SURFACES MUST BE COMPLY WITH THE ARCHITECTURAL ALUMINUM MFGS. ASSOC. STANDARDS FOR FORCED ENTRY o
OF ALL FLOORS, PRIOR TO HANDING THE COMPLETED PROJECT OVER TO THE OWNER. THROUGHLY CLEANED PRIOR TO THE INSTALLATION OF THE TILE SETTING BED. INSTALLATION RESISTANCE, AAMA 1303.3.
OF MATERIALS CONSTITUTES ACCEPTANCE OF THE SURFACES. 10. DOORS AND WINDOWS: ALL EXTERIOR SLIDING GLASS DOORS AND WINDOW MUST BE APPROVED
7. MATERIALS: BY DADE COUNTY PRODUCT APPROVAL.
INSTALLATION SHALL BE IN ACCORDANCE WITH THE LATEST EDITION OF THE CERAMIC TILE � r
ALL MATERIALS SHALL BE NEW, AS CALLED FOR IN THE DRAWINGS, AND THE BEST OF THEIR INSTITUTE'S MOST RECENT INSTALLATION MANUAL. THE FINISHED TILE SURFACE SHALL BE w
RESPECTIVE KINDS. NO SUBSTITUTIONS SHALL BE MADE BY THE CONTRACTOR WITHOUT PRIOR LEVEL WITH NO BUMPS OR RIDGES. GROUTED JOINTS SHALL BE STRAIGHT AND OF CONSIS-
WRITTEN APPROVAL BY THE OWNER, UNLESS SPECIFIED OTHERWISE IN THE DRAWINGS. FOR TENT WIDTH. INSTALLATIONS NOT IN ACCORDANCE WITH THESE SPECIFICATIONS WILL BE
PORTIONS OF THE WORK NOT SHOWN IN DETAIL, BUT WHICH ARE SHOWN GENERALLY, OR REJECTED AND THE CONTRACTOR WILL BE RESPONSIBLE FOR REDOING THE WORK AT HIS CQ
ARE REASONABLY INFERRIBLE AS BEING REQUIRED FOR A COMPETENT AND COMPLETE OWN EXPENSE.
INSTALLATION, THE MATERIAL, METHODS AND WORKMANSHIP SHALL CONFORM AS A MINIMUM
TO THE TYPICAL OR REPRESENTATIVE DETAIL THROUGHOUT CORRESPONDING PARTS OF THE ALL CERAMIC TILE SHALL BE CLEANED, POLISHED AND LEFT IN PERFECT CONDITION AT THE T�
BUILDING. COMPLETION OF THE WORK. PROVIDE PROTECTION FOR ALL FINISHED SURFACES BEFORE (J1
PERMITTING ACCESS TO THE AREAS BY OTHERS.
8. FIRE RESISTIVITY: 3. VINYL TILE AND RESILIENT FLOORING:
WHERE ASSEMBLIES OF THEIR VARIOUS COMPONENTS, MATERIALS, OR CONSTRUCTION SYSTEMS ALL VYNIL TILE, RESILIENT FLOORING, ADHESIVES AND ACCESSORIES SHALL BE SUPPLIED AND
ARE INDICATED TO HAVE FIRE RESISTIVITY RATINGS, UNDERWRITERS LABORATORY RATINGS, ETC., INSTALLED BY THE CONTRACTOR UNLESS NOTED OTHERWISE. INSTALLATIONS SHALL BE IN ARCHITECTURE
THE STANDARDS ESTABLISHED THE GOVERNING CODES IN ORDER TO ACHIEEV
ALL SUCH SHALL S COMPOSED OF MATERIALS AND BE ASSEMBLED SO AS CONFORM ACCORDANCE WITH INDUSTRY'S STANDARDS. WHEN NECCESSARY FLOORING SHALL BE CARE-
RATING IN THE COMPLETED WORK. E THE REQUIR ED R FULLY JOINED TO CONTINUE PATTERNS WITHOUT INTERRUPTIONS.
4. CARPETING AND PADDING:
9. CUTTING AND PATCHING:
ALL CARPETING AND PADDING SHALL BE SUPPLIED AND INSTALLED BY THE CONTRACTOR
EACH CONTRACTOR SHALL BE RESPONSIBLE FOR ANY CUTTING, FITTING, PATCHING, AND UNLESS NOTED OTHERWISE. INSTALLATION SHALL BE IN ACCORDANCE WITH ALL INSUSTRY
MATCHING OF HIS NEW WORK TO EXISTING WORK., WHERE APPLICABLE AND INDICATED IN STANDARDS.
THE DRAWINGS. NO CONTRACTOR SHALL ENDANGER ANY WORK OF ANY OTHER CONTRACTOR
BY EXCAVATING, CUTTING OR OTHERWISE ALTERING ANY WORK OF ANY OTHER CONTRACTORS. 5. PAINTING AND STAINING:
ROOFING SHALL BE INSPECTED BY A CERTIFIED ROOFING CONTRACTOR TO DETERMINE WATER
TIGHTNESS AT EXISTING ROOFING THAT IS PENETRATED OR OTHERWISE ALTERED BY NEW WORK. ALL SUFACES WALLS, CEILINGS, DOORS, WOODWORK AND TRIM, ETC. SHALL BE SANDED
ROOFING CONTRACTOR SHALL REPAIR AND PATCH SUCH AREAS AS REQUIRED OR AS SMOOTH AND FULLY PREPATED TO RECEIVE FINISHES AS SPECIFIED HEREIN.
INDICATED IN THE DRAWINGS, TO THE EXTENT THAT THE ROOF SHALL BE BONDABLE. ALL
NEW BUILT UP ROOFING TO BE 3-PLY WITH HOT ASPHALT MOPPING OF EACH 30 LB. PATCHED WALLS SHALL BE PAINTED FLOOR TO CEILING, CONER TO CORNER, TO MATCH EXIST-
ROOFING FELT. ING. IF COLOR MATCH IS NOT POSSIBLE, THE ARCHITECT SHALL BE NOTIFIED AND THE v
ENTIRE ROOM SHALL BE REPAINTED.
10. DEMOLITION: ALL PATCHED CEILINGS SHALL BE PAINTED CORNER TO CORNER.
THE CONTRACTOR SHALL BE RESPONSIBLE FOR THE DEMOLITION AND REMOVAL OF DEBRIS
OF ALL EXISTING INTERIOR PARTITIONS AS REQUIRED TO COMPLETE THE CONSTRUCTION AS WOOD JOINTS TO BE PAINTED SHALL BE TIGHT FITTING, OR FULLY FILLED AND SANDED SMOOTH. G E N E F A R M E R
SPECIFIED ON THE DRAWINGS. EXISTING UNUSED ELECTRIC AND PLUMBING SHALL BE REMOVED WOOD JOINTS TO BE STAINED SHALL BE TIGHT FITTING AND SANDED SMOOTH. &
AND ADEQUATELY CAPPED AS ALLOWED BY CODE.
ALL WOOD AND METALS SHALL BE SANDED SMOOTH BETWEEN EACH COAT OF PAINT MATERIAL A S S 0 C I A T E S
APPLIED. THE TERM SMOOTH MUST BE INTERRUPTED TO MEAN FREE FROM ALL ROUGHNESS,
11. PROTECTION OF PROPERTY:
RIDGES, RUNS, SAGS AND PROJECTIONS ON THE SURFACE. ARCHITECTS - PLANNERS
THE CONTRACTOR SHALL PROTECT ALL ADJACENT PROPERTY, ROADS, AND WALKS FROM ALL MATERIALS SHALL BE APPLIED AS PER THE MANUFACTURER'S RECOMMENDATIONS. ALLOW
DAMAGE DURING THE COURSE OF CONSTRUCTION. ALL DAMAGE TO SAID PROPERTY, ROADS, 24 HOURS DRYING TIME BETWEEN COATS. 13321 SOUTHWEST 124 STREET
AND WALKS SHALL BE REPAIRED BY THE CONTRACTOR AT HIS OWN EXPENSE. 19AMI,FL./F00006B/305-235-7400
ALL PAINT AND STAIN SHALL BE APPLIED BY BRUSH OR ROLLER UNLESS SPECIFIED OTHERWISE.
12. UTILITIES:
ALL MATERIALS TO BE APPLIED SMOOTHLY AND EVENLY AND TO BE FREE FROM HOLIDAYS ARCHITECT
THE CONTRACTOR SHALL PROVIDE AND PAY ALL CONSTRUCTION WATER AND ELECTRICITY, AND VARIATIONS IN SHEEN AND COLOR. IN THE EVENT OF "HOT SPOTS" OR "SUCTION SPOTS"
INCLUDING ALL TEMPORARY WASTE AND ELECTRICAL INSTALLATIONS , AND FOR DISPOSAL OF AFTER SUCH APPLICATION, THESE SPOTS ARE TO BE TOUCHED UP TO GIVE AN EVEN SHEEN
ALL SPILLED BUILDING WATER. BEFORE APPLYING THE SECOND COAT.
13. BASE WATERPROOFING: THE CONTRACTOR SHALL APPLY THREE FOOT SQUARE COLOR SAMPLES OF ALL PAINT COLORS
AND OBTAIN THE ARCHITECT'S APPROVAL PRIOR TO CONTINUING THE APPLICATION. ;
IN ANY AREA WHERE THE FINISHED GRADE IS TO BE HIGHER THAN THE FINISHED FLOOR
LEVEL, THAT PORTION OF THE WALL IS TO BE COATED WITH ONE HEAVY COAT OF BITUMASTIC ACCEPTABLE PRODUCTS INCLUDE: BENJAMIN MOORE, DUPONT, PPG, SHERWIN-WILLIAMS DEVOE,
WATERPROOFING, TO PREVENT WATER INFILTRATION. THE INSIDE WALL SURFACE OF ALL RAISED PRATT AND LAMBERT. SUBSTITUTIONS MUST HAVE THE ARCHITECT'S APPROVAL PRIOR TO
PLANTERS SHALL ALSO BE COATED WITH BITUMASTIC WATERPROOFING. PURCHASE OR APPLICATION.
GENE FARMER RA
14. TERMITE TREATMENT: EXTERIOR SURFACES: AR 7565
THE CONTRACTOR SHALL PROVIDE AN APPROVED METHOD OF TERMITE TREATMENT TO SOILS A. STUCCO: 2 COATS BENJAMIN MOORE MOOREGARD EXTERIOR LATEX HOUSE PAINT.
AROUND ALL FOOTINGS AND UNDER CONCRETE SLABS. B. UNPRIMED METAL: 1 COAT OF PRIMER AND 2 COATS OF ENAMEL.
C. FACTORY PRIMED METAL: 1 COAT OF PRIMER AND 1 COAT OF ENAMEL. CONSULTANT
15. DISSIMILAR METALS: D. STAIN FINISH WOOD: 1 COAT OF "WOODLIFE" AND 2 COATS OF "OLYMPIC" SEMI
TRANSPARENT STAIN.
THE CONTRACTOR SHALL PROTECT AGAINST ELECTROLYTIC ACTION BETWEEN DISSIMILAR METALS
BY WRAPPING POINTS OF CONTACT WITH INDUSTRIAL FABRIC TAPE AND COAT WITH HEAVY INTERIOR SURFACES:
BODY BITMINOUS PAINT OR OTHER ELECTRICAL INSULATION.
A. PLASTER AND DRYWALL WALLS: 2 COATS OF SATIN OR SEMI FLAT LATEX PAINT.
16. SUBSTITUTIONS: B. BATHROOM, KITCHEN, UTILITY WALLS: 2 COATS OF ENAMEL.
C. DOORS, WOODWORK AND TRIM PAINT FINISH): 1 COAT PRIMER AND 2 COATS OF ENAMEL.
WHERE THE PRODUCT OF A CERTAIN MANUFACTURER IS SPECIFIED, NO SUBSTITUTION WILL D. DOORS, WOODWORK AND TRIM (STAIN FINISH): 2 COATS OF STAIN AND 2 COATS OF
BE ACCEPTED DURING THE BIDDING PHASE. AFTER A CONTRACTOR HAS BEEN SELECTED, VARNISH.
SUBSTITUTIONS MAY BE PRESENTED TO THE ARCHITECT FOR APPROVAL IF SAID SUBSTITUTION
IS EQUAL IN QUALITY AND PERFORMANCE TO THOSE SPECIFIED IN THE WORKING DRAWINGS
AND SPECIFICATIONS, AND IS IN STRICT ACCORDANCE WITH ALL GOVERNING BUILDING CODES.
17. JOB SUPERVISOR:
THE GENERAL CONTRACTOR SHALL HAVE A QUALIFIED SUPERVISORY REPRESENTATIVE ON THE
PROD
JOB SITE AT ALL TIMES WORK IS BEING DONE, BY ANY SUB-CONTRACTOR TO OVERSEE AND
COORDINATE THE VARIOUS ELEMENTS OF THE JOB.
DATE 5-07-01 A = 5
BY EDF OF 5