Loading...
00-1329 SP2 NOTE PROTRUDING OBJECTS (CONT'D) WATER CLOSETS (CONT'D) HANDRAILS. GRAB BARS, AND TUB SIGNAGF. THIS DOCUMENT SETS GENERAL GUIDELINES FOR ACCESSIBI- 4.4.2 WALKS, HALLS, CORRIDORS, PASSAGEWAYS, AISLES, OR OTHER 4.16.5 * FLUSH CONTROLS SHALL BE HAND OPERATED OR AUTOMATIC AND SHOWER SEATS (CONT'D) 4.30.4 * LETTERS AND NUMERALS SHALLBE RAISED 1/32", UPPER LITY TO PLACES OF PUBLIC AL GUIDELINES AND COMMERCIAL CIRCULATION SPACES SHALL HAVE 80" MINIMUM CLEAR HEAD AND SHALL COMPLY WITH 4.27.4. CONTROLS FOR FLUSH (5) GRAB BARS SHALL NOT ROTATE WITHIN THEIR FITTINGS. CASE, SANS SERIF OR SIMPLE SERIF STYLE AND SHALL BE [Do FACILITIES BY INDIVIDUALS WITH DISABILITIES. PLEASE ALSO ROOM (SEE FIG 8(A)). IF A VERTICAL CLEARANCE OF AN VALVES SHALL BE MOUNTED ON THE WIDE SIDE OF TOILET ACCOMPANIED WITH GRADE 2 BRAILLE. RAISED CHARACTERS REFER TO ALL APPLICABLE CODES FOR ADDITIONAL HANDI- AREA ADJOINING AN ACCESSIBLE ROUTE IS REDUCED TO LESS AREAS NO MORE THAN 44" ABOVE THE FLOOR. 4.26.4 A HANDRAIL OR GRAB BAR AND ANY WALL OR OTHER SUR- SHALL BE AT LEAST 5/8" HIGH, BUT NO HIGHER THAN T PICTOGRAMS SHALL BE ACCOMPANIED BY THE EQUIVALENT CAP ACCESSIBILITY REQUIREMENTS. THAN 80" (NOMINAL DIMENSION), A BARRIER TO WARN BLIND FACE ADJACENT TO IT SHALL BE FREE OF ANY SHARP OR TLY OR VISUALLY-IMPAIRED PERSONS SHALL BE PROVIDED (SEE 4.16.6 TOILET PAPER DISPENSERS SHALL BE INSTALLED WITHIN REACH ABRASIVE ELEMENTS. EDGES SHALL HAVE A MINIMUM RADIUS VERBAL DESCRIPTION PLACED DIFOF BELOW THE PICTO- OE FIG. 8(C-1)). AS SHOWN IN FIG. 29 (B). DISPENSERS THAT CONTROL DE- OF 1/8". BE 6" MINIMUM IN 1OF DIMENSION HEIGHT. THE PICTOGRAM SHALL DATE EMIS/ISSUED LIVERY, OR THAT DO NOT PERMIT CONTINUOUS PAPER FLOW, 4.5 GROUND AND FLOOR SURFACES SHALL NOT BE USED. NOV. 8th, 2000 FOR PERMIT 2.0 GENERAL 4.27 CONTROLS AND OPERATING MECHANISMS 4.30.5 * THE CHARACTERS AND BACKGROUND OF SIGNS SHALL BE * GROUND AND FLOOR SURFACES ALONG ACCESSIBLE ROUTES 4.19 LAVATORIES AND MIRRORS 4.27.1 CONTROLS AND OPERATING MECHANISMS REQUIRED TO BE EGGSHELL, MATTE, OR OTHER NON-CLARE FINISH. CHARAC- 2.1 THE SPECIFICATIONS IN THESE GUIDELINES ARE BASED UPON 4.5.1 AND IN ACCESSIBLE ROOMS AND SPACES INCLUDING FLOORS, TERS AND SYMBOLS SHALL CONTRAST WITH THEIR BACK- ADULT DIMENSIONS AND ANTHROPOMETRICS. ACCESSIBLE BY 4.1 SHALL COMPLY WITH 4.27. GROUND-EITHER LIGHT CHARACTERS ON A DARK BACKGROUND DEC. 1st, 2000 FOR LANDLORD, BIDS 8 STOREFRONT PERMIT WALKS, RAMPS, STAIRS, AND CURB RAMPS, SHALL BE STABLE 4.19.1 THE REQUIREMENTS OF 4.19 SHALL APPLY TO LAVATORY FIX- OR DARK CHARACTERS ON A LIGHT BACKGROUND. FIRM, SLIP RESISTANT,NT, AND SHALL COMPLY WITH 4.5. TURES, VANITIES, AND BUILT-IN LAVATORIES. 4.27.2 CLEAR FLOOR SPACE COMPLYING WITH 4.2.4 THAT ALLOWS A .I REQUIREMENTS R THIS GUIDELINE T USE OF OTHER DESIGNS FORWARD OR A PARALLEL APPROACH BY A PERSON USING 4.30.6 WHERE PERMANENT IDENTIFICATION IS PROVIDED FOR ROOMS AN, O8, 2001 FOR GONSTRUGTION 2.2 DEPARTURES FROM PARTICULAR TECHNICAL AND SLOPING AND TECHNOLOGIES ARE PERMITTED WHERE THE ALTERNATIVE 4.5.2 CHANGES IN LEVEL UP TO 1/4" MAY BE VERTICAL AND WITHOUT 4.19.2 LAVATORIES SHALL BE MOUNTED WITH THE RIM OR COUNTER DESIGNS AND TECHNOLOGIES USED WILL PROVIDE SUBSTANTI- EDGE TREATMENT (SEE FIG 7(C)). CHANGES IN LEVEL BETWEEN SURFACE NO HIGHER THAN 34" ABOVE THE FINISH FLOOR. RECEPTACLES, AND OTHER OPERABLE EQUIPMENT. 1/4" AND 1/2' SHALL BE BEVELED WITH A SLOPE NO GREATER PROVIDE A CLEARANCE OF AT LEAST 29" ABOVE THE FINISH IS NO L THE LATCH SIDE OF THE DOOR. WHERE THERE JAN, 25, 2001 FOR PERMIT ADDENDUM OF THE FACILITY. THAN 1:2 (SEE FIG 7(D)). CHANGES IN LEVEL GREATER THAN FLOOR TO THE BOTTOM OF THE APRON. KNEE AND TOE 4.27.3 THE HIGHEST OPERABLE PART OF CONTROLS, DISPENSERS, C D WALL SPACE TL THE LATCH SIDE OF THE DOOR, IN- ALLY EQUIVALENT OR GREATER ACCESS TO AND USABILITY 1/2" SHALL BE ACCOMPLISHED BY MEANS OF A RAMP THAT CLEARANCE SHALL COMPLY WITH FIG. 31. RECEPTACLES, AND OTHER OPERABLE EQUIPMENT SHALL BE LUI NG AT DOUBLE LEAF DOORS, SIGNS SHALL BE PLACED COMPLIES WITH 4.7 OR 4.8. PLACED WITHIN AT LEAST ONE OF THE REACH RANGES SPE- ON THE NEAREST ADJACENT WALL. MOUNTING HEIGHT SHALL BE 60" ABOVE THE FINISH FLOOR PTO THE CENTERLINE OF THE 4.2 SPACE ALLOWANCE AND REACH RANGES 4.19.3 A CLEAR FLOOR SPACE 30" BY 48" COMPLYING WITH 4.2.4 CIFIED IN 4.2.5 AND 4.2.6. ELECTRICAL AND COMMUNICAT- SIGN. MOUNTING LOCATION FOR SUCH SIGNAGE SHALL BE SO 4.5.3 * IF CARPET OR CARPET TILE IS USED ON A GROUND OR FLOOR SHALL BE PROVIDED IN FRONT OF A LAVATORY TO ALLOW IONS SYSTEM RECEPTACLES ON WALLS SHALL BE MOUNTED THAT A PERSON MAY APPROACH WITHIN 3" OF SIGNAGE WITH- 4.2.1 * THE MINIMUM CLEAR WIDTH FOR SINGLE WHEELCHAIR PASSAGE SURFACE, THEN IT SHALL BE SECURELY ATTACHED: HAVE A FORWARD APPROACH. SUCH CLEAR FLOOR SPACE SHALL NO LESS THAN 15" ABOVE THE FLOOR. OUT ENCOUNTERING PROTUDING OBJECTS OR STANDING WITHIN SHALL BE 32' AT A POINT AND 36" CONTINUOUSLY ADJOIN OR OVERLAP AN ACCESSIBLE ROUTE AND SHALL EX- { )) FIRM CUSHION, PAD, OR BACKING, OR NO CUSHION OR PAD: THE SWING OF A DOOR. (SEE FIG. 1 AND 24 E AND HAVE A LEVEL LOOP, TEXTURED LOOP, LEVEL CUT PILE, TEND A MAXIMUM OF 19" UNDERNEATH THE LAVATORY (SEE EXEPTION: THESE REQUIREMENTS DO NOT APPLY WHERE THE OR LEVEL CUT/UNCUT PILE TEXTURE. THE MAXIMUM PILE FIG. 32). USE OF SPECIAL EQUIPMENT DICTATES OTHERWISE OR WHERE 4.30.7 * (1) FACILITIES AND ELEMENTS:REQUIRED TO BE IDENTIFIED 4.2.2 THE MINIMUM WIDTH FOR TWO WHEELCHAIRS TO PASS IS 60" THICKNESS SHALL BE 1/2" (SEE FIRG. 8(F)). EXPOSED EDGES ELECTRICAL AND COMMUNICATIONS SYSTEMS RECEPTACLES ARE (SEE FIG. 2). OF CARPET SHALL BE FASTEND TO FLOOR SURFACES AND 4.18.4 HOT WATER AND DRAIN PIPES UNDER LAVATORIES SHALL BE NOT NORMALLY INTENDED FOR USE BY BUILDING OCCUPANTS. AS ACCESSIBLE BY IL SHALL USE THE INTERNATIONAL * THE SPACE REQUIRED FOR A WHEELCHAIR TO MAKE A 180 HAVE TRIM ALONG THE ENTIRE LENGHT OF THE EXPOSED INSULATED OR OTHERWISE SHALL BE CONFIGURED OR ABRASIVE AGAINST SYMBOL OF ACCESSIBILITY. THE SYMBOL SHALL BE DIS 4.2.3 PLAYED AS SHOWN IN FIG. 43(A) AND (B) EDGE. CARPET EDGE TRIM SHALL COMPLY WITH 4.5.2. 4.27.4 CONTROLS AND OPERATING MECHANISMS SHALL BE OPERABLE DEGREE TURN IS A CLEAR SPACE OF 60" DIAMETER OR A CES UNDER LAVATORIES. WITH ONE HAND AND SHALL NOT REQUIRE TIGHT GRASPING, / ,i ! i ' ; 0g" " T-SHAPED SPACE 4.5.4 IF GRATINGS ARE LOCATED IN WALKING SURFACES, THEN THEY PUNCHING, OR TWISTING OF THE WRIST. THE FORCE REQUIRED ' ;; ' (SEE FIG. 3(B)). SHALL HAVE SPACES NO GREATER THAN 1 2" WIDE IN ONE 4.19.5 FAUCETS SHALL COMPLY WITH 4.27.4. LEVER-OPERATED, TO ACTIVATE CONTROLS SHALL BE NO GREATER THAN 5 LBF % " / DIRECTION (SEE FIG. 8(G)). IF GRATINGS H PUSH-TYPE, AND ELECTRONICALLY CONTROLLED MECHANISMS (22,2 N). AVE ELONGATED ARE EXAMPLES OF ACCEPTABLE DESIGNS. IF SELF-CLOSING �1 4.2.4 * CLEAR FLOOR OR GROUND SPACE FOR OPENINGS, THEN THEY SHALL BE PLACED SO THAT THE LONG DOMINANT DIRECTION VALVES ARE USED THE FAUCET SHALL REMAIN OPEN FOR AT DIMENSION IS PERPENDICULAR TO THE 8 ALARMS WHEELCHAIRS. LEAST 10 SECONDS. OF TRAVEL (SEE FIG. 8(H)). 4 2 4.2.4.1 THE MINIMUM CLEAR FLOOR OR GROUND SPACE REQUIRED TO 4.28.1 ALARM SYSTEMS REQUIRED TO BE ACCESSIBLE BY 4.1 SHALL r ACCOMODATE A SINGLE, STATIONARY WHEELCHAIR AND 4.19.6 MIRROS SHALL BE MOUNTED WITH THE BOTTOM EDGE OF THE k�1DEIf�� �1> REFLECTING SURFACE NO HIGHER THAN 40" ABOVE THE FINISH COMPLY WITH 4.28. AT A MINIMUM, VISUAL APPLIANCES SHALL �{ ! SH L BE PROVIDED IN BUILDINGS AND FACILITIES IN EACH OF THE OCCUPANT IS 30" BY 48" (SEE FIG. 4(A)). THE MINIMUM 4.13 DOORS LQ( �A L CLEAR FLOOR OR GROUND SPACE FOR WHEELCHAIRS MAY BE 4.13.1 DOORS REQUIRED TO BE ACCESSIBLE BY 4.1 SHALL COMPLY FLOOR (SEE FIG. 31). FOLLOWING AREAS: RESTROOMS AND ANY OTHER GENERAL r.:: 1AN1 � POSITIONED FOR FORWARD OR PARALLEL APPROACH TO AN WITH THE REQUIREMENTS OF 4.13. USAGE AREAS (E.G., MEETING ROOMS), HALLWAYS, LOBBIES, OBJECT (SEE FIG. 4(B) AND (C)). CLEAR FLOOR OR GROUND 4.22 TOILET ROOMS AND MANY OTHER AREA FOR COMMON USE. SPACE FOR WHEELCHAIRS MAY BE PART OF THE KNEE SPACE 4.13.2 REVOLVING DOORS OR TURNSTILES SHALL NOT BE THE ONLY �2 REQUIRED UNDER SOME OBJECTS. MEANS OF PASSAGE AT AN ACCESSIBLE ENTRANCE OR ALONG 4.22.1 TOILET FACILITIES REQUIRED TO BE ACCESSIBLE BY 4.1 SHALL 4,28,2 * IF PROVIDED, AUDIBLE EMERGENCY ALARMS SHALL PRODUCE COMPLY WITH 4.22. ACCESSIBLE TOILET ROOMS SHALL BE A SOUND THAT EXCEEDS THE PREVAILING EQUIVALENT SOUND ' Al/' AN ACCESSIBLE ROUTE. AN ACCESSIBLE GATE OR DOOR SHALL 4.2.4.2 ONE FULL UNOBSTRUCTED SIDE OF THE CLEAR FLOOR OR BE PROVIDED ADJACENT TO THE TURNSTILE OR REVOLVING ON AN ACCESSIBLE ROUTE. LEVEL IN THE ROOM OR SPACE BY AT LEAST 15 DBA OR GROUND SPACE FOR A WHEELCHAIR SHALL ADJOIN OR OVERLAP DOOR AND SHALL BE SO DESIGNED AS TO FACILITATE THE EXCEEDS ANY MAXIMUM SOUND LEVEL WITH A DURATION OF AN ACCESSIBLE ROUTE EE ADJOIN ANOTHER WHEELCHAIR SAME USE PATTERN. 4.22.2 ALL DOORS TO ACCESSIBLE TOILET ROOMS SHALL COMPLY 60 SECONDS BY 5 DBA, WHICHEVER IS LOUDER. SOUND LE- EE Om 28" WITH 4.13.CLEAR FLOOR SPACE. IF A CLEAR FLOOR SPACE IS LOCATED DOORS SHALL NOT SWING INTO CLEAR FLOOR VELS FOR ALARM SIGNALS SHALL NOT EXCEED 1 20 DBA. IN AN ALCOVE OR OTHERWISE CONFINED ON ALL OR PART OF 4.13.3 GATES, INCLUDING TICKET GATES, SHALL MEET ALL APPLI- SPACE REQUIRED FOR ANY FIXTURE. THREE SIDES, ADDITIONAL MANEUVRING CLEARANCES SHALL CABLE SPECIFICATION OF 4.13. 4.28.3 * VISUAL ALARM SIGNAL APPLIANCES SHALL BE INTEGRATED BE PROVIDED AS SHOWN IN FIG. 4(D) AND (E). 4.22.3 * THE ACCESSIBLE FIXTURES AND CONTROLS REQUIRED IN 4.22.4, INTO THE BUILDING OR FACILITY ALARM SYSTEM. IF SINGLE 4.22.5, 4.22.6, AND 4.22.7 SHALL BE ON AN ACCESSIBLE STATION AUDIBLE ALARMS ARE PROVIDED THEN SINGLE STA- ROUTE. AN UNOBSTRUCTED TURNING TION VISUAL 4.13.4 IF DOORWAYS HAVE TWO INDEPENTLY OPERATED DOOR LEAVES, RNING SPACE COMPLYING WITH IAL ALARM SIGNALS SHALL BE PROVIDED. VISUAL END OF ACCESSIBILITY GUIDELINES 4.2.4.3 CLEAR FLOOR OR GROUND SPACES FOR WHEELCHAIRS SHALL THEN AT LEAST ONE LEAF SHALL MEET THE SPECIFICATIONS COMPLY WITH 4.5. IN 4.13.5 AND 4.13.6. THAT LEAF SHALL BE AN ACTIVE LEAF. 4.2.3 SHALL BE PROVIDED WITHIN AN ACCESSIBLE TOILET ALARM SIGNALS SHALL HAVE THE FOLLOWING MINIMUM PHO- FOR BUILDINGS AND FACILITIES ;w P`•:+•••••.� ROOM. THE CLEAR FLOOR SPACE AT FIXTURES AND CONTROLS, TOMETRIC AND LOCATION FEATURES: � �- 4.2.5 * IF THE CLEAR FLOOR SPACE ONLY ALLOWS FORWARD APPROACH 4.13.5 DOORWAYS SHALL HAVE A MINIMUM CLEAR OPENING OF 32" THE ACCESSIBLE ROUTE, AND THE TURNING SPACE MAY OV- �•�� •• / TO AN OBJECT, THE MAXIMUM HIGH FORWARD REACH ALLOWED WITH THE DOOR OPEN 90 DEGREES, MEASURED BETWEEN THE ERLAP. (1) THE LAMP SHALL BE A XENON STROBE TYPE OR EQUI- *� �c SHALL BE 48" (SEE FIG. 5(A)). THE MINIMUM LOW FORWARD FACE OF THE DOOR AND THE OPPOSITE STOP (SEE FIG. 24(A), VALENT. REACH IS 15". IF THE HIGH FORWARD REACH IS OVER AN (B), C), AND (D)). OPENING MORE THAN 24" IN DEPTH SHALL 4.22.4 IF TOILET STALLS ARE PROVIDED, THEN AT LEAST ON SHALL •r ( ) ( A STANDARD TOILET STALL COMPLYING WITH 4.17; WHERE } o •41 OBSTRUCTION, REACH AND CLEARANCES SHALL BE AS SHOWN COMPLY WITH 4.2.1 AND 4.3.3 (SEE FIG. 24(E)). BE (2) THE COLOR SHALL BE CLEAR OR NOMINAL WHITE (LE. IN FIG. 5(8). 6 OR MORE STALLS ARE PROVIDED, IN ADDITION TO THE STALL UNFILTERED OR CLEAR FILTERED WHITE LIGHT). EXCEPTION: DOORS NOT REQUIRING FULL USER PASSAGE, COMPLYING WITH 4.17.3, AT LEAST ONE STALL 36" WIDE WITH / {t� 4.2.6 * IF THE CLEAR FLOOR SPACE ALLOWS PARALLEL APPROACH SUCH AS SHALLOW CLOSETS, MAY HAVE THE CLEAR OPENING AN OUTWARD SWINGING, SELF-CLOSING DOOR AND PARALLEL (3) THE MAXIMUM PULSE DURATION SHALL BE TWO-TENTHS 'el s(; *c••e••• �� BY A PERSON IN A WHEELCHAIR, THE MAXIMUM HIGH SIDE REDUCE TO 20" MINIMUM. GRAB BARS COMPLYING WITH FIG. 30(D) AND 4.26 SHALL BE OF ONE SECOND (0.2 SEC.) WITH A MAXIMUM DUTY CYCLE ` �° ^' REACH ALLOWED SHALL BE 54" AND THE LOW SIDE REACH PROVIDED. WATER CLOSETS IN SUCH STALLS SHALL COMPLY OF 40 PERCENT. THE PULSE DURATION IS DEFINED AS SHALL BE NO LESS THAN 9" ABOVE THE FLOOR (FIG. 6(A) 4.13.6 MINIMUM MANEUVRING CLEARANCES AT DOORS THAT ARE NOT WITH 4.16. IF WATER CLOSETS ARE NOT IN STALLS, THEN THE TIME INTERVAL BETWEEN INITIAL AND FINAL POINTS AND (B)). IF THE SIDE REACH OVER AN OBSTRUCTION, THE AUTOMATIC OR POWER-ASSISTED SHALL BE AS SHOWN IN FIG. AT LEAST ONE SHALL COMPLY WITH 4.16. OF 10 PERCENT OF MAXIMUM SIGNAL. REACH AND CLEARANCES SHALL BE AS SHOWN IN FIG 6(C). 25. THE FLOOR OR GROUND AREA WITHIN THE REQUIRED CLEARANCES SHALL BE LEVEL AND CLEAR. 4.22.5 IF URINALS ARE PROVIDED, THEN AT LEAST ONE SHALL COM- (4) THE INTENSITY SHALL BE A MINIMUM OF 75 CANDELA. PLY WITH 4.18. 4.3 ACCESSIBLE ROUTE EXCEPTION: ENTRY DOOR TO ACUTE CARE HOSPITAL BEDROOMS (5) THE FLASH RATE SHALL BE A MINIMUM OF 1 HZ AND 4.3.1 * ALL WALKS, HALLS, CORRIDORS, AISLES, SKYWALKS, TUNNELS FOR IN-PATIENTS SHALL BE EXEMPTED FROM THE REQUI- 4.22.6 IF LAVATORIES AND MIRROS ARE PROVIDED, THEN AT LEAST A MAXIMUM OF 3 HZ. AND OTHER SPACES THAT ARE PART OF AN ACCESSIBLE REMENT FOR SPACE AT THE LATCH SIDE OF THE DOOR (SEE ONE OF EACH SHALL COMPLY WITH 4.19. ROUTE SHALL COMPLY WITH 4.3. DIMENSION "X" IN FIG. 25) IF THE DOOR IS AT LEAST 44 HI THE APPLIANCE SHALL BE PLACED 80" ABOVE THE WIDE. 4.22.7 IF CONTROLS, DISPENSERS, RECEPTACLES, OR OTHER EQUIP- HIGHEST FLOOR LEVEL WITHIN THE SPACE OR 6" BELOW 4.3.2 AT LEAST ONE ACCESSIBLE ROUTE WITHIN THE BOUNDARY OF MENT ARE PROVIDED, THEN AT LEAST ONE OF EACH SHALL THE CEILING WHICHEVER IS LOWER. THE SITE SHALL BE PROVIDED FROM PUBLIC TRANSPORTATION 4.13.7 THE MINIMUM SPACE BETWEEN TWO HINGED OR PIVOTED DOORS BE ON AN ACCESSIBLE ROUTE AND SHALL COMPLY WITH 4.27. NO. DATE REVISION STOPS, ACCESSIBLE PARKING, AND ACCESSIBLE PASSENGER IN SERIES SHALL BE 48" PLUS THE WIDHT OF ANY DOOR (7) IN GENERAL, NO PLACE IN ANY ROOM OR SPACE LOADING ZONES, AND PUBLIC STREETS OR SIDEWALKS TO THE SWINGING INTO THE SPACE. DOORS IN SERIES SHALL SWING 4.25 STORAGE REQUIRED TO HAVE A VISUAL SIGNAL APPLIANCE SHALL ACCESSIBLE BUILDING ENTRANCE THEY SERVE. THE ACCE- EITHER IN THE SAME DIRECTION OR AWAY FROM THE SPACE BE MORE THAN 50 FT. FROM THE SIGNAL (IN THE HORI- CONTRACTOR MUST VERIFY ALL SSIBLE ROUTE SHALL, TO THE MAXIMUM EXTENT FEASIBLE, BETWEEN THE DOORS (SEE FIG. 26). 4.25.1 FIXED STORAGE FACILITIES SUCH AS CABINETS, SHELVES, ZONTAL PLANE). IN LARGE ROOMS AND SPACES EXCEE- DETAILS, SPECIFICATIONS AND COINCIDE WITH THE ROUTE FOR THE GENERAL PUBLIC. CLOSETS, AND DRAWERS REQUIRED TO BE ACCESSIBLE BY DING 100 FT. ACROSS, WITHOUT OBSTRUCTIONS 6 FT. DIMENSIONS, AND REPORT ANY 4.13.8 * THRESHOLDS AT DOORWAYS SHALL NOT EXCEED 3/4" IN HEIGHT 4.1 SHALL COMPLY WITH 4.25. ABOVE THE FINISH FLOOR, SUCH AS AUDITORIUMS, DEVI- DISCREPANCIES TO OWNER AT LEAST ONE ACCESSIBLE ROUTE SHALL CONNECT ACCESSIBLE FOR EXTERIOR SLIDING DOORS OR 1/2" FOR OTHER TYPES OF CES MAY BE PLACED AROUND THE PERIMETER, SPACED BEFORE PROCEEDING WITH WORK BUILDINGS, FACILITIES, ELEMENTS AND SPACES THAT ARE ON DOORS. RAISED THRESHOLDS AND FLOOR LEVEL CHANGES AT 4.25.2 A CLEAR FLOOR SPACE AT LEAST 30" BY 48" COMPLYING A MAXIMUM 100 FT. APART, IN LIEU OF SUSPENDING THE SAME SITE. ACCESSIBLE DOORWAYS SHALL BE BEVELED WITH A SLOPE WITH 4.2.4 THAT ALLOWS EITHER A FORWARD OR PARALLEL APPLIANCES FROM THE CEILING. �n�n ��nn MM nn n /� � AT LEAST ONE ACCESSIBLE ROUTE SHALL CONNECT ACCESSIBLE NO GREATER THAN 1:2 (SEE 4.5.2). APPROACH BY A PERSON USING A WHEELCHAIR SHALL BE DD Eu HUO 7. UV/ U TCHIEL L QoDoL=� PROVIDED AT ACCESSIBLE STORAGE FACILITIES. (8) NO PLACE IN COMMON CORRIDORS OR HALLWAYS IN BUILDING OR FACILITY ENTRANCES WITH ALL ACCESSIBLE SPACES 4.13.9 * HANDLES, PULLS, LATCHES, LOCKS, AND OTHER OPERATING WHICH VISUAL ALARM SIGNALLING APPLIANCES ARE RE- Consulting Architect - AND ELEMENTS AND WITH ALL ACCESSIBLE DWELLING UNITS DEVICES ON ACCESSIBLE DOORS SHALL HAVE A SHAPE THAT 4.25.3 ACCESSIBLE STORAGE SPACES SHALL BE WITHIN AT LEAST QUIRED SHALL BE MORE THAN 50 FT. FROM THE SIGNAL. WITHIN THE BUILDING OR FACILITY. IS EASY TO GRASP WITH ONE HAND AND DOES NOT REQUIRE ONE OF THE REACH RANGES SPECIFIED IN 4.2.5 AND 4.2.6 A. TIGHT GRASPING, TIGHT PINCHING, OR TWISTING OF THE WRIST (SEE FIG. 5 AND FIG. 6). CLOTHES RODS OR SHELVES SHALL 4.28.4 * UNITS AND SLEEPING ACCOMODATIONS SHALL HAVE A VISUAL I. N. INC. 1 AN ACCESSIBLE ROUTE SHALL CONNECT AT LEAST ONE ACCE- TO OPERATE. LEVER-OPERATED MECHANISMS, PUSH-TYPE BE A MAXIMUM OF 54" ABOVE THE FINISH FLOOR FOR A SIDE ALARM CONNECTED TO THE BUILDING EMERGENCY ALARM 1521 N. Cooper, Suite 600 SSIBLE ENTRANCE OF EACH ACCESSIBLE DWELLING UNIT THOSE MECHANISMS, AND U-SHAPED HANDLES ARE ACCEPTABLE APPROACH. WHERE THE DISTANCE FROM THE WEELCHAIR TO SYSTEM OR SHALL HAVE A STANDARD 110-VOLT ELECTRICAL Arlington, Texas 76001 EXTERIOR AND INTERIOR SPACES AND FACILITIES THAT SERVE DESIGNS. WHEN SLIDING DOORS ARE FULLY OPEN, OPERATING THE CLOTHES ROD OR SHELF EXCEED 10" (AS IN CLOSETS RECEPTACLE INTO WHICH SUCH AN ALARM CAN BE CONNEC- Tel: (817) 265-2415 Fax: (817) 277-0571 THE ACCESSIBLE DWELLING UNIT. HARDWARE SHALL BE EXPOSED AND USABLE FROM BOTH SIDES. WITHOUT ACCESSIBLE DOORS) THE HEIGHT AND DEPTH TO THE TED AND A MEANS BY WHICH A SIGNAL FROM THE BUILDING HARDWARE REQUIRED FOR ACCESSIBLE DOOR PASSAGE SHALL ROD OR SHELF SHALL COMPLY WITH FIG. 38(A) AND FIG. 38(B). EMERGENCY ALARM SYSTEM CAN TRIGGER SUCH AN AUXILIARY 4.3.3 THE MINIMUM CLEAR WIDTH OF AN ACCESSIBLE ROUTE SHALL BE MOUNTED NO HIGHER THAN 48" ABOVE FINISH FLOOR. ALARM. WHEN VISUAL ALARMS ARE IN PLACE THE SIGNAL BE 36" EXCEPT AT DOORS (SEE 4.13.5 AND 4.13.6). IF A 4.25.4 HARDWARE FOR ACCESSIBLE STORAGE FACILITIES SHALL COM- SHALL BE VISIBLE IN ALL AREAS OF THE UNIT OR ROOM. ARCHITECTURE + DESIGN PERSON IN A WHEELCHAIR MUST MAKE A TURN AROUND AN 4.13.10 * IF A DOOR HAS A CLOSER, THEN THE SWEEP PERIOD OF THE PLY WITH 4.27.4. TOUCH LATCHES AND U-SHAPED PULLS INSTRUCTIONS FOR USE OF THE AUXILIARY ALARM OR RECEP- Montrbal St-Louis OBSTRUCTION, THE MINIMUM CLEAR WIDTH OF THE ACCESSIBLE CLOSER SHALL BE ADJUSTED SO THAT FROM AN OPEN POSI- ARE ACCEPTABLE. TACLE SHALL BE PROVIDED. ROUTE SHALL BE AS SHOWN IN FIG. 7(A) AND (B). TION OF 70 DEGREES, THE DOOR WILL TAKE AT LEAST 3 SECONDS TO MOVE TO A POINT 3" FROM THE LATCH, MEAS- 4.26 HANDRAILS GRAB BARS, AND TUB 4.29 DETECTABLE WARNINGS tlsdueClac. 4.3.4 IF AN ACCESSIBLE ROUTE HAS LESS THAN 60" CLEAR WIDTH, URED TO THE LEADING EDGE OF THE DOOR. AND SHOWER SEATS 4521 Suite 00 THEN PASSING SPACES AT LEAST 60" BY 60" SHALL BE 4.29.1 DETECTABLE WARNINGS REQUIRED BY 4.1 AND 4.7 SHALL Suite 300 LOCATED AT REASONABLE INTERVALS NOT TO EXCEED 200 FT. 4.13.11 * THE MAXIMUM FORCE FOR PUSHING OR PULLING OPEN A DOOR 4.26.1 * ALL HANDRAILS, GRAB BARS, AND TUB AND SHOWER SEATS COMPLY WITH 4.29. Moanaaa112T2T] A T-INTERSECTION OF TWO CORRIDORS OR WALKS IS AN SHALL BE AS FOLLOWS: REQUIRED TO BE ACCESSIBLE BY 4.1, 4.8, 4.9, 4.16, 4.17, Canada8f2T2T3 4.20 OR 4.21 SHALL COMPLY WITH 4.26. 4.29.2 * DETECTABLE WARNINGS SHALL CONSIST OR RAISED TRUNCA- T 514844-6611 ACCEPTABLE PASSING PLACE. (1) FIRE DOORS SHALL HAVE THE MINIMUM OPENING FORCE TED DOMES WITH A DIAMETER OF NOMINAL 0.9", A HEIGHT F 514W-7646 4.3.5 ACCESSIBLE ROUTES SHALL COMPLY WITH 4.4.2 ALLOWABLE BY APPROPRIATE ADMINISTRATIVE AUTHORITY. 4.26.2 * THE DIAMETER OR WIDTH OF THE GRIPPING SURFACES OF A OF NOMINAL 0.2" AND A CENTER-TO-CENTER SPACING OF www.aedifica.com 4.3.6 THE SURFACE OF AN ACCESSIBLE ROUTE SHALL COMPLY (2) OTHER DOORS: HANDRAIL OR GRAB BAR SHALL BE 1 1/4" TO 1 1/2" OR THE NOMINAL 2.35" AND SHALL CONTRAST VISUALLY WITH AD- - JOINING SURFACES, EITHER LIGHT-ON-DARK, SHAPE SHALL PROVIDE AN EQUIVALENT GRIPPING SURFACE. OR DARK-ON- Q. PE WITH 4.5. IF HANDRAILS OR GRAB BARS ARE MOUNTED ADJACENT TO LIGHT. (A) EXTERIOR HINGED DOORS: (RESERVED) A WALL, THE SPACE BETWEEN THE WALL AND THE GRAB BAR t 4.3.7 AN ACCESSIBLE ROUTE WITH A RUNNING SLOPE GREATER THAN SHALL BE 1 1/2" (SEE FIG. 39(A), (B), (C), AND (E)). HAND- 4.29.5 THE MATERIAL USED TO PROVIDE CONTRAST SHALL BE LE v �O 1:20 IS A RAMP AND SHALL COMPLY WITH 4.8. NOWHERE (B) INTERIOR HINGED DOORS: 5 LBF (22.2N) RAILS MAY BE LOCATED IN A RECESS IF THE RECESS IS A INTEGRAL PART OF THE WALKING SURFACE. DETECTABLE SHALL THE CROSS SLOPE OF AN ACCESSIBLE ROUTE EXCEED MAXIMUM OF 3" DEEP AND EXTEND AT LEAST 18" ABOVE THE WARNINGS USED ON INTERIOR SURFACES SHALL DIFFER FROM 1:50. (C) SLIDING OR FOLDING DOORS: 5 LBF (22.2N) ( ( ADJOINING WALKING SURFACES IN RESILIENCY OR SOUND-ON- 4 TOP OF THE RAILS SEE FIG. 39 D)). CANE CONTACT. 4.3.8 CHANGES IN LEVELS ALONG AN ACCESSIBLE ROUTE SHALL THESE FORCES DO NOT APPLY TO THE FORCE REQUIRED TO 4.26.3 THE STRUCTURAL STRENGTH OF GRAB BARS, TUB AND SHOWER J COMPLY WITH 4.5.2. IF AN ACCESSIBLE ROUTE HAS CHANGES RETRACT LATCH BOLTS OR DISENGAGE OTHER DEVICES THAT SEATS, FASTENERS, AND MOUNTING DEVICES SHALL MEET THE 4.29.6 IF A WALK CROSSES OR ADJOINS A VEHICULAR WAY, AND q`DO GAO IN LEVEL GREATER THAN 1/2", THEN A CURB RAMP, RAMP, MAY HOLD THE DOOR IN A CLOSED POSITION. FOLLOWING SPECIFICATIONS: THE WALKING SURFACES ARE NOT SEPARATED BY CURBS, ELEVATOR, OR PLATFORM LIFT (AS PERMITTED IN 4.1.3 AND RAILINGS, OR OTHER ELEMENTS BETWEEN THE PEDESTRIAN 905 RUE HODGE 4.1.6) SHALL BE PROVIDED THAT COMPLIES WITH 4.7, 4.8, 4.13.12 * IF AN AUTOMATIC DOOR IS USED, THEN IT SHALL COMPLY (1) BENDING STRESS IN A GRAB BAR OR SEAT INDUCED AREAS AND VEHICULAR AREAS, THE BOUNDARY BETWEEN 4.10 OR 4.11, RESPECTIVELY. AN ACCESSIBLE ROUTE DOES WITH ANSI/BHMA A156.10-1985. SLOWLY OPENING, LOW- BY THE MAXIMUM BENDING MOMENT FROM THE APPLICA- THE AREAS SHALL BE DEFINED BY A CONTINUOUS DETECTA- VILLE ST-LAURENT NOT INCLUDE STAIRS, STEPS, OR ESCALATORS. SEE DEFINITION POWERED, AUTOMATIC DOORS SHALL COMPLY WITH ANSI TION OF 250 LBF (1112 N) SHALL BE LESS THAN THE BLE WARNING WHICH IS 36" WIDE, COMPLYING WITH 4.29.2. QUEBEC, CANADA H4N 21913 OF "EGRESS, MEANS OF" IN 3.5, A156.19-1984. SUCH DOORS SHALL NOT OPEN TO BACK ALLOWABLE STRESS FOR THE MATERIAL OF THE GRAB BAR CHECK FASTER THAN 3 SECONDS AND SHALL REQUIRE NO OR SEAT. 4.30 SIGNAGE (514 747-2536 4.3.9 DOORS ALONG AN ACCESSIBLE ROUTE SHALL COMPLY WITH MORE THAN 15 LBF (66.6N) TO STOP DOOR MOVEMENT. IF FAX: (514) 747-7993 4.13. A POWER-ASSISTED DOOR IS USED, ITS DOOR-OPENING FORCE (2) SHEAR STRESS INDUCED IN A GRAB BAR OR SEAT BY 4.30.1 * SIGNAGE REQUIRED TO BE ACCESSIBLE BY 4.1 SHALL COMPLY SHALL COMPLY WITH 4.13.11 AND ITS CLOSING SHALL CONFORM THE APPLICATION OF 250 LBF (1112 N) SHALL BE LESS WITH THE APPLICABLE PROVISIONS OF 4.30. 4.3.10 * ACCESSIBLE ROUTES SERVING ANY ACCESSIBLE SPACES OR TO THE REQUIREMENTS IN ANSI A156.19-1984. THAN THE ALLOWABLE SHEAR STRESS FOR THE MATERIAL ELEMENT SHALL ALSO SERVE AS A MEANS OF EGRESS FOR OF THE GRAB BAR OR SEAT. IF THE CONNECTION BET- 4.30.2 * LETTERS AND NUMBERS ON SIGNS SHALL HAVE A WIDTH- PROJET PROJECT: EMERGENCIES OR CONNECT TO AN ACCESSIBLE AREA OF 4.16 WATER CLOSETS WEEN THE GRAB BAR OR SEAT AND ITS MOUNTING BRA- TO-HEIGHT RATIO BETWEEN 3:5 AND 1:1 AND STROKE-WIDTH- ALDO space# 154 RESCUE ASSISTANCE. CKET OR OTHER SUPPORT IS CONSIDERED TO BE FULLY TO-HEIGHT RATIO BETWEEN 1:5 AND 1:10. 4.16.1 ACCESSIBLE WATER CLOSETS SHALL COMPLY WITH 4.16. RESTRAINED, THEN DIRECT AND TORSIONAL SHEAR STRES- 5HOP5 AT 5UN5ET PLACE 4.4 PROTRUDING OBJECTS SSES SHALL BE TOTALED FOR THE COMBINED SHEAR STRESS 4.30.3 CHARACTERS AND NUMBERS ON SIGNS SHALL BE SIZED AC- 4.16.2 CLEAR FLOOR SPACE FOR WATER CLOSETS NOT IN STALLS WHICH SHALL NOT EXCEED THE ALLOWABLE SHEAR STRESS. CORDING TO THE VIEWING DISTANCE FROM WHICH THEY ARE 5OUTH MIAMI, FL. 4.4.1 * OBJECTS PROJECTING FROM WALLS (FOR EXAMPLE, TELEPHONES) SHALL COMPLY WITH FIG. 28. CLEAR FLOOR SPACE MAY BE TO BE READ. THE MINIMUM HEIGHT IS MEASURED USING AN WITH THEIR LEADING EDGES BETWEEN 27" AND 80" ABOVE ARRANGED TO ALLOW EITHER A LEFT-HANDED OR RIGHT- (3) SHEAR FORCE INDUCED IN A FASTENER OR MOUNTING UPPER CASE X. LOWER CASE CHARACTERS ARE PERMITTED. THE FINISHED FLOOR SHALL PROTRUDE NO MORE THAN 4" HANDED APPROACH. DEVICE FROM THE APPLICATION OF 250 LBF (1112 N) SHALL TITRE/TITLE: INTO WALKS, HALLS, CORRIDORS, PASSAGEWAYS, OR AISLES //�� BE LESS THAN THE ALLOWABLE LATERAL LOAD OF EITHER HEIGHT ABOVE MINIMUM ��//�� (SEE FIG. 8(A)). OBJECTS MOUNTED WITH THEIR LEADING 4.16.3 * THE HEIGHT OF WATER CLOSETS SHALL BE 17" TO 19" MEA- THE FASTENER OR MOUNTING DEVICE OR THE SUPPORTING FINISH FLOOR CHARACTER HEIGHT �Ll'�-5PEGIIGATIONS EDGES AT OR BELOW 27" ABOVE THE FINISHED FLOOR MAY SURED TO THE TOP OF THE TOILET SEAT (SEE FIG. 29(8)). STRUCTURE, WHICHEVER IS THE SMALLER ALLOWABLE LOAD. PROTRUDE ANY AMOUNT (SEE FIG. 8(A) AND (B)). FREE- SEATS SHALL NOT BE SPRUNG TO RETURN TO A LIFTED SUSPENDED OR PROJECTED 3" MINIMUM PROJET N0./PROJECT NO. DESSINE/DRAWN: STANDING OBJECTS MOUNTED ON POSTS OR PYLONS MAY POSITION. (4) TENSILE FORCE INDUCED IN A FASTENER BY A DIRECT OVERHEAD IN OVERHANG 12" MAXIMUM FROM 27" TO 80" ABOVE THE GROUND TENSION FORCE OF 250 LBF (1112 N) PLUS THE MAXIMUM COMPLIANCE WITH 4.4.2 U-612 G•G• OR FINISHED FLOOR (SEE FIG. 8(C) AND (D)). PROTRUDING 4.16.4 * GRAB BARS FOR WATER CLOSETS NOT LOCATED IN STALLS MOMENT FROM THE APPLICATION OF 250 LBF (1112 N) OBJECTS SHALL NOT REDUCE THE CLEAR WIDTH OF AN ACCE- SHALL COMPLY WITH 4.26 AND FIG. 29. THE GRAB BAR SHALL BE LESS THAN THE ALLOWABLE WITHDRAWAL LOAD ECHELLE/SCALE: VERIFI CHECKED: K.Z. SSIBLE ROUTE OR MANEUVRING SPACE (SEE FIG. 8(B)). BEHIND THE WATER CLOSET SHALL BE 36" MINIMUM. BETWEEN THE FASTENER AND THE SUPPORTING STRUCTURE. DATE: PAGE: H:\2-Comm\AIdo\Shops at Sunset Place\ARCHITECTURAL\DESSINS\GENERAL\NEW CEILING\U612-SP2.dwg NOS/. ed, 2000 PLOT TIME: JAN 25, 2001 [10:06]