06-774-012.'.Or
VIPJ''�
CONCRETE BASE-
W 16X6 -10110 WWF
1)om - PROVIDE ANCHOR BOLT WITH A MINIMUM OF 500 POUND
PULL-OUT RESISTANCE. SHALL SECURE THE AIR CONDITIONING
CONDENSER UNIT FROM WITHIN THE UNIT TO THE CONCRETE SLAB
ON WHICH THE UNIT RESTS TO WITHSTAND 150 MPH HURRICANE FORCE.
2) -UNITS SHALL BE CLEAR BY 3" MIN. FROM DRIP LINE.
A S.FASTENED OE AT EACH SUP 2 "m x 1 -112"
PORT) AND
PROVIDE SOLID ISOLATION PAD
FOR CORROSION INHIBITOR
SUCTION LINE
W/ 112 ARMAFLEX
INSULATION do VAPOR
BARRIER
C.U. MOUNTING DETAIL
N.T.9
SPLIT A/C SYSTEM SCHEDULE
INIT NUMBER A141.1-2
too
MANU=ACTURER
RI-EEM
MODEL NU!"MR
ww -I1
�V
TOTAL CF1'1.
100
O/A CFJt
0
H
ENT. AIR TEMP. (F)
80/61
SENSIBLE COOLING (BTUH)
18,000
TOTAL COOLING (BTUH)
24 ;00
BLOIl,ER MOTOR HP.
1/3
J
VOLTAGE
230 -1 -60
MAX. BREAKER SIZE
25
=
UNIT UEIGNT (LBSJ
OL
MATCHING CONDENSING UNIT
ACCT! -2
4
ELECTRIC
1E4TER
au
50
BTUH
Il fd00
STAGE
1
VOLTAGE
230 -1 -60
UNIT NJ1SER
ACCU-2
MAMFACTURER
RHEEM
MODEL NUMBER
RAMC- 024JAB
}-
NOMNAL TONS
210
NUMBER OF COMPRESSORS
1
RLA EACH
109
LRA. EACH
54
ZL1
NUMBER OF CONDENSER FANS
I
FLA EACH
0 9
VOLTAGE
230 -1 -60
MAX. BREAKER SIZE
25
UNIT QE*W
145
SYSTEM E.E.R. / SEER
140
LIQUID LINE (N)
46
SUCTION LINE (IN)
%
AREA SERVED
FAMILY ROOM
GENERAL H.V.A.C. NOTES
I- MCHANICAL CONTRACTOR SMALL 1
A) Verify all space conditions and dimensions at job
site prior to fabrication of ductwork and installation
of equipment.
B) Coordinate work with other trades.
C) Do all work In accordance with state and local codes.
D) Do all work in accordance either latest ASHRAE guide
and SMACNA standards.
E) Pay for all permits, fees, inspections and testing.
F) Adjust and balance diffuser in accordance with
quantities shown on plans.
G) Submit shop drawings to engineer for approval.
H) Furnish all labor material and equipment
for a complete H.V.A.C. system in accordance with
referenced standards and these drawings.
J) (") these doors with 314" under cut.
2- GUARANTEES s
A) All new equipment and materials shall be guarantee
for one year after date of acceptance. All compressors
shall carry standard factory 5 year guarantee.
B) Provide 90 day free service.
3 - A/C DUCTS s
Shall be constructed of 1.5" thick R -6.0 insulation
value, standard duty fiberglass board flameproof
reinforced aluminum faced cover in accordance with
N.F.P.A. No. 90A and as manufactured by Owens -
Corning. Ductwork shall be fabricated and installed
according with manufacturer is instruction. Install air
volume extractors at each duct tap.
- If round / flexible duct is used then shall be 2" thick
with R -6.0 insulation.
- Duct sizes shown are net free area inside.
- All air devices (diffusers, registers and grilles) shall be all
aluminum construction, with exposed surface chemically treated to
receive point to match color or AIRGUIDE or approved equal.
- Provide opposed blade dampers at all diffusers and registers.
- Thermostats shall be combination cooling /heating with system
Cool /Auto /Heat /Off and Fan On /Auto selector switches.
- Refrigerant piping shall be copper type V with 314" armaflex.
Insulation shall be provided for suction lines.
- Provide new filters for fan coil before starting. These
filters must also be replaced prior to final acceptance by owner.
4- VENTILATION DUCTS s
Shall be constructed of galvanized sheet metal and
sized as per plans or drawings shown.
5- EXISTING CONDITIONS s(Ir applicable)
A) Contractor Fs t f miliarti a hhimself rt existing
conditions in t�elc� pnor 17 Ing and /h ors art of
construction.
B) Contractor to reuse most of the existing grilles as
possible only after cleaning has been done if owner
allowed.
POWER do CONTROL
LOCATION
LIQUID LINE W/ 0
INSULATION
I
L
INES
/L
SUCTION CONNECTION PLUG I
LIQUID CONNECTION CLEANOUT % L
11/2" LONG "HILTV POUTER
SLAB
ACTIVATED � ,INTO � � A H U
PROVIDE 4" PVC SLEEVE
a FOR 125 TO 3 TONS t 6"
PVC SLEEVE FOR 3.5 TO 5
TONS IF REFRIG. LINES RUN
UNDER SLAB
CONDENSING UNIT MOUNTING DETAIL
N.T.S.
HORIZONTAL UNION
RUN.PITCH
1 /8 " /FT TRAP DEPTH AS
SHOWN OR AS
REQUIRED TO MAKE
, J J�ROPER SEAL
/0�� Su.
CONDENSATE CONN. TO A/C UNIT
N.T.S.
DDUBLE THICKh
TURNING V/
ELBOW WITH TURNING
VANES DETAIL
N.T.S.
DUCT
NOTE
1. X =2" FOR UNITS UP TO 3 TONS.
2. X =3" FOR UNITS OVER 3 TONS.
3. CONNECTIONS TO THE UNIT DRAIN
PANS MAY BE EITHER FLEXIBLE
CONNECTIONS OR RIGID PIPING.
FLEXIBLE CONNECTIONS USED
TO FORM A TRAP SHALL NOT
EXCEED 18 INCHES IN LENGTH
4. THE UNIT DRAIN PAN IS PART
OF THE EQUIPMENT.
L-
EX15T.
C.U. *1
A.G.G.U.
n
MECHANICAL PLAN
SCALE 1/4" = 1`0
REVISIONS
BY
too
CH mom O
:5
asp AS S 4ovW-V
�V
,,Ilium
7,w/x, AI
,APR 2 12006
ro
¢Mt b
i-
Q
�0 �w
W� ^
00
ft
50
U
I. V) �. a
cn W 0
F•
U _Q n•�
W s
Q
•.s
4A
x�
�WUJ
� Q
U d-
� p Q
o W UJ
a: F-p
o c C) I� O�
Z � J
Q Z
O Q
�F=\10�
U Q
l7�
Q
maw - - -
too
CH mom O
_ _
1M% ----- q_O -9-
asp AS S 4ovW-V
,,Ilium