5943 SW 62 ST EB-93-227-002 sw tpa,(;�
SECURITY AND FORCED ENTRY PREVENTION UJ
UJ
I. GENE I,
SCOPE: The following prescribes requirements for security (c) EXTERIOR WINDOWS: Z , REQUIREMENTS EASED ON OCCUPANCY
and forced entry prevention for all buildings and structures (1) Exterior windows shall be locked with a device
regulated by the South Florida Building Code (Dade County). an the inside capable of withstanding a force of 150 pounds GROUP I OCCUPANCIES:
(a) Buildings of Group".
APPLICATION: Every building and structure shall be secured applied in any operable direction unless the window opening g p I Occupancy shall be provided
is protected by other intrusion security devices as set forth with intrusion and bur
and protected against forced entry as required in these herein or an a glary security devices as set forth in R.
,
notes, where conflict exists between a provision of these approved equivalent. Section III of these notes and as follows:
notes and a provision of the S.F.B.C., the provision 11 W
(2) Exterior windows used as means of escape shall (b) (1) swinging g
establishing the highest standard of life safety shall gin exterior doors and doors connecting
also comply with Section 3111 of the South Florida Building garage areas with living areas shalt comply with Section III
supersede, Cade (Dade County), of these notes and shall be secured with a latch and a single
"
t TI. DEFINITIONS AND STANDARDS (ta COMPONENTS OTHER THAN LOCKS shall comply in design dead bolt with one-inch minim throw, or a combination
deadlatch and dead bolt set or dead bolt which contain an
DEFINITIONS: For purposes of these notes, certain terms are
or installation as follows: insert, each with a one-inch minimum throw.
defined as follows. Other definitions used herein shall be
(1) Hinges, with hinge pins exposed to the outside, C!
as set forth in Section 401 of the South Florida Building (2) Main entrance doors shall be provided with a 4
e
of all exterior doors, operable windows, transoms, skylights door scope or vision panels complying with Section III„ o€
Code (Dade County}. and access scuttles shall have nonremovable
o€ intalki pins, or shall be these notes, � ,�
(a) BURGLAR-RESISTANT roc n
T MATERIAL: Glazing materials g-stud type and such hinges shall have _
complying with UL972 and the applicable testing provisions of nonexposed screws. D.to
ASTlt 01036. (2) ,Iambs of all exterior of fset-type insw£ngiag
(b) COMBINATION DEAD LATCH AND DEAD BOLT: A device doors shall be rabbeted, or of similar fabrication, to
(
1101 ,-r to combining a dead latch operable by knobs from inside and prevent defeating the purpose of the strike and the integrity
outside and a dead bolt operable from inside by thumbturn and of the latches.
from outside by key, both of which can be retracted from
inside by turning the knob and outside by key. (3) (aa) wood Jambs shall be secured at a minimum
(o) CYLINDER GUARD: A free-turning hardened steel ring of points 6 of anchoring per vertical side.
or a recessed plate surrounding the otherwise exposed portion (bb} Sub books shall be of pressure-treated
E 4! T Wk4 of a cylinder lock to prevent cutting, drilling, prying, material at least 2 inches nominal thickness, and secured in g
TO T� 1 pulling, or wrenching with co on tools. at least 6 points on each leg with 3 inch or equivalent CL `g
_ (d) DEAD LATCH: A latch which is positively held in fasteners.
latched position with a strike by an added, integral
S C fC t( (cc) Jambs shall be provided with approved
} a bolt-type mechanism and is again released by a key from the
F � � reinforcing strikes installed with screws at least 3 inches
outside and by a knob or similar actuator from the inside. in length. Screws shall a
C ,I, � e�� 1 g penetrate subbuoks to a depth of at
C -- least 1 inch.
(e) DEAD LATCH: A locking device with a bolt, not spring
r ib C- t Lo 6 loaded, which engages and disengages a strike by the use of (4) (as) Steel frames shall be installed in
e ( key from the outside and by the same key or a th turn or
� � t �'°°°' �` e�”°'�� -t� i similar actuator from the inside. accordance with manufacturer's recommendstians, and shall
meet the standards of the National Association of Metal
IC �LJ ° !P I& Manufacturers and G ?. Exterior frame material shall be of
are F. 1T wor- � l ( (f) OR SCOPE: A system of lenses encased for a minimum 16-gauge steel.
f` { 1 convenient installation in entrance doors permitting an
0" � : ( inside viewer to observe a 160 degree area of the outside t)
r G� _ (5) Exterior doors for areas requiring security
r^°v r° with the doer closed.
�� � � .,� shall be designed and constructed as set forth in Section II
-�
i (g) DOUBLE DEAD BOLT: A dead lock actuated by the same of these notes.
l 1 f ) / 2 key from the inside and outside, (6) Glazing other than in doors and within 40
inches of the inside looking device of doors to the exterior
C¢(w k LA,-iii a3C1 �p« I Ch) INSERT« BOLT: A hardened steel taller inside shall comply with standard set forth in the Standards
ii.�° , s t , ' " unhardened bolts to prevent bolt cutting with common tools. section of these notes, art C or be
k 1 l T T p Protected as provided in Z�;
lj I f tom( Section IV of these notes, we
/ / & p t (i) LATCH: A spring-loaded device which automatically
l t holds a swinging door shut upon closing by engaging a strike q glass doors and horizontally
�^ f (7) (aa) Slidin
j and which is again released by turning a knob, lever, or sliding windows shall be constructed and installed so that no
i ".rZ. t similar actuator from inside or outside. panel can be lifted from the tracks when in a locked position
l �$ � and provided with locks as set forth in Section III of these
a ¢ (j) LOUVERS: A series of removable, fixed-slanted, or notes.
°N, movable slats. Glass-louvered is descriptive of jalousies.
1 Glass, wood, or metal jalousies are considered to be louvers. (bb) Such doors and windows shall also comply
Awning-type windows having sections more than 12 inches in with the resistance standards set forth in Section TI of
" °° 1 depth are not considered to be louvers. these notes.
( (k) MULTIPLE POINT COCA: A system of lever-operated �n4 ents in overhead-type garage doors not
t bolts that engage a door opening, at least at the head and exceed A in least dime nsion and shall be located
�g ,� $ ( sill, operated by single knob or handle from the inside and, closer tin Valdl�e i de -activating device. le"y`
HF-. t $ T rz- Ji:vPL optionally, by cylinder-locked handle from the outside. � `=5
LCh� C (4) Metal a Be-ty doors providing
& (I) BINDLE DEAD BOLT= A dead lock actuated from the intrusion and b ry security steal o designed and `g \x
4Z1 outside by a key and from the inside by a knob, thu turn, installed the doors cannot be removed fro. e tracks I l
lever, or similar actuator other than a key. whe acted position. ei
(m) SLIDING DOOR nEAD BOLT: A single dead bolt which, (10) Doors with louvers, as defined herein„ shall d
tt �p T lCft after penetration of the strike, expands, or is a not be installed in the exterior walls of areas of requiring 0 71
pivoted-hook type, to resist sliding the door by force. security unless the louvered area is protected as
Section IV of these notes, or by approved ppraved provided e.
_
(n) STRIKE: A stationary, metal plate designed to device.
f momentarily depress a moving latch for final secure (11) (aa) All windows shall be constructed so that 44
engagement requiring a separate operation for disengagement. where fixed or locked they cannot be removed from the frames �
r from outside unless the window opening is protected as 1I3 � it ul -
STANDARDS: The standards referenced in these notes shall be
1 V
provided In Section of these notes, or by an approve: ll.( Cl
those set forth in Section 402 of the South Florida Building equivalent security devivi se. l3 � C9)
Code (Dade CO ty).
OL
(a) Burglar-resistant lass shall comply with AS C (bb) Windows so protected and used as means of Lli
g p y escape shall comply with Section 3111.
1036 for polished plate glass. LL
(e) DOORS TO EXTERIOR FROM AREAS REQUIRING SECURITY: tS
(b) Tests of burglar-resistant glazing materials shall Doors to exterior from areas requiring security shall meet
comply with the Underwriter's Laboratories Standard for the fallowing requirements:
Safety of Burglar Resistant Glazing Material, UL72, 0
(c) Glass and glass-like materials shall comply with the (1) WOOD DOORS: Where wood doors are permitted.by m-
p y the South Florida Building Code (Dade County), the design and
American National Standards Institute (ANSI) Standard for construction shall be as follows:
Transparent Safety Glazing Material used in Buildings,°Z97,1.
(aa) Swinging doors, where of solid Dare,
(d) Aluminum windows shall comply with the Architectural flush construction, shall be not less than 1 3/9 inches in
Aluminum Mana.tacturer's Association ( A) Standard for thickness.
Forced-Entry Resistant Horizontal Sliding windows, A
1302.5, and ANSI/A 101. (bb) Solid cores of particle woad shall not be
g glass dears shall comply with the
eD
(e) Sliding permitted,
Architectural Aluminum Manufacturers' Association (A AMA) (cc) Swinging doors of stile, rail and panel
Standard for Forced Entry Resistant Aluminum Sliding Glass. construction shall have rails and stiles not less than 1 3/4
Doors, RAMA 1303.5° and ANSI/A 101. inches in thickness with retaining tongues or splines not
efM g� t (' �C 111. GENERAL REQUIREMENTS
less than 3/S inch least dimension.
d � " t (dd) Overhead-type wood garage doors I
°1 APPLICATION: comply � Subparagraph 3103.6(a)C2) of the So brid
OF
®0017 Building Co ade County} and shall not b ss than 1.3/a
(a) The requirements of this section shall apply to all inches in thickn except, where o nel constructon,
buildings and structures subject to compliance with these inset panels shall no be less an 3/9 inch thick, C-C
notes. grade, exterior plywood c . it,h the NBS Standard PS-1,
6
or the equivalent in r h, ided that such panels
s ( (b) Such buildings and structures shall also comply with within 40 inches he inside
'at locking devices
LOT I `� the requirements for the specific group of 'occupancy set panels, ess than 24
are backed a e inside with steel
T T Oft A r I forth in Section IV, gauge, red to resist a load not less thannwcause
f re of the wood inset panels.
` a` � DOORS AND DOOR LOCKS: (f) Swinging dears of stile, rail and glazed
(a) GENERAL: As required by occupancy in Section IV,
7 �° construction shall have rails and stiles not less than 1 3/4
" '
the fallowing provisions shall be applicable: inches in thickness and shall be glazed as follows:
(1) Exterior exit doors, if operable from exterior, (1) Glazing in doors to the exterior, except
shall have at least one lock that is key-operated from the sliding glass doors complying with paragraphs (b) and (d) of
f°� exterior, this subsection, shall not be permitted within 40 inches of
inside latching and locking devices unless protected as
(2) Locks on exterior doors shall be a minimum of provided in Section Iv of these notes, or by an approved
6,000 possible key changes or locking combinations. equivalent security device.
(3) DEAD BOLTS ON EXTERIOR DOORS: (2) Where permitted in exterior doors, glazing !
shall comply with resistance standards set forth in Section
(aa) Exterior doors serving as primary means IF of these notes.
of egress shall be equipped with a combination dead latch and
dead bolt device which shall comply with 3103.2(d) of the g G DOORS;
South Florida Building Code (Dade County) and Section II of
y
these Hates, conventional full-sized„ metal woad°framed
C F -mm " r tiding glass do shall samply with on III of these
r (bb) where only a latch set is specified for otes and Paragraph .2(c) of t outh Florida Building
�. t�,1° ° a B FI-I(�a° 1� �?d V�( A14 T %A$1 � exterior doors not serving as a component of a required path ode (Dade County).
fim • > / 7 � y�� r° r l?• of egress„ either a combination dead latch and dead bolt V
p 9 lockset or an auxiliary dead bolt shall be provided, and the
(2) Ca & tonal swinging gla ors shall comply
pp° B device used shall comply with Section II of these notes. with Seckio I of these notes and (b)(1) paragraphs
t-1",:� OF- eft ��Ld�'�°G� �B CC �; �� C'.� L 5, 3506.3 and
g° �� (#) of the South Florida Building (Dade
(4) Dead bolts shall be hardened or contain y).
inserts.
` ^ Gil GC, o aG a" R'? ',✓ ../ ' . ;o" ak, .
C5) Alternative devices (h) OTHER TERIALS: Exterior doors constructed of
� w� � � providing equivalent materials other than wood or glass, except as specified in
resistance to illegal entry, such as but not limited to, paragraph (d) herein, shall be acceptable
provided the
p
combination locks may be substituted subject to approval by completed assembly:
• - � t�p - "-�° I p:o;:. # ' y the building official where such devices comply with
310342(d) of the South Florida Building Code (Dade County)
(1) Resists the forces due to wind leads, as
and the resistance standards set forth in Section I of these required in Section 2304 of the South Florida Building Code UJ
& notes.
(Dade County) and complies with all ether applicable
(6) Locks on doors, where such locks are required provisions of that Code.
to be intrusion-and burglar-resistant, shall be capable of
(l Is et capable of resisting forced entry as the
resisting a force of 300 pounds applied in any movable
wood assembli es set forth in paragraph (a) herein.
direction and otherwise in accordance with the resistance
standards set forth in Section I of these notes. (i) METAL OVERHEAD-T1P Metal overhead-type Gaza
do s shall, in lieu of other requirements of this cha er,
(7) Dead bolts shall have a bevelled, hardened reet he following requirements:
cylinder guard on the exterior side of door. p
(8) Connecting screw heads of dead bolts shall not 1) Formed or extruded aluminum shall 0.027 of
ran inch min in thickness.
be exposed on the exterior side of door, or shall be of
tamper-resistant design. (2) F med steel shall be not lea ban 24 gauge. LU
(b) Application of locks to 7orat er doors shall be - (3) Maxi m deflection o panels in open,
f lows: horizontal position sh I be 1/120 o he span.
(1) (as) The active leapairs of swingin (4) Materials not eeting the requirements
doors o the exterior shall have ls required for ingle specified herein may be s i he design and construction
swingi doors or be provided wiltiple-point ocks or of such doers provided sue hall be limited to the area
multiple oint locks which contaserts, reach ith 5/E 5 or more feet above the or si
inch thro bolts and a cylinder lo
(5) Windlo s and eaten guide-roller shafts
(bb) The egress sithe i ctive leaf of shall prevent door sections from bei unseated from the
pairs of swinging doors to the ior sh 1 be provided tracks when subje to loads less than wo d cause failure of
multiple point ,locks; or flush urfa bolts top and the section.
bottom, each with°.minim 5/9 inch w a 1/2 inch minimum The completed assembly shall rest the forces
engagement, \
t due to w loads and set forth in Section 2304 o the South
(2) (aa) tiding glass in exterior walls and Florid Building Code (Dade County), shall com with
accessible from the outside shalprovided with sliding Para aph 3103.2(c) of the South Florida Building Cad (Dade
door dead bolts, or a bolt or pin removable or operable Ca ty) and other applicable provisions of that Code, nd
from the exterior, at the jamb, he ill, or at the meeting all also comply with Subparagraph 3103.2(b)(3) of the Sam
mullions, LU
(bb) Sue d s 11 be reinforced in the �
strike and lock area to main n bolt strength effectiveness
where necessary to me?t the equ rements set forth herein.
(cc) Such ears she have no screws removable APPROVED
from the outside which if remove would facilitate ready IS O ( 1; i
entry, nor shall any door leaf whe closed and locked be � 1 9
1p pu,q+,,°r¢°^re ce ">( ry x^Y'3 — $$ •e, q as
openablar from the au ide.
(3) (as Overhead-type and acc dion type doors in
exterior walls s 11 be provided with molt' le-insert locks,
or be locked a more than one point with h dened bolts, or BEST {
Zi arts, engaging at least 2 op site points a
f 5 of an inch.
(bb) Other locking devices on such core shall
uired where the doors are controlled and coked by
ower.(4) Metal grates and grille-type doors, here intrusion and burglary security, shall be pro ded s as for other doors and shall bd designed aching the inside actuator from outside. °Q,.