Loading...
09-629-050• r- 4 O O N O N ELECTRICAL SPECIFICATIONS SCOPE A INCLUDES THE FURNISHING OF ALL LABOR, SUPERVISION, MATERIALS, EQUI ", TOOLS, ETC., REQUIRED FOR THE ELECTRICAL SYSTEMS AS SHOWN AND DESCRIBED IN THESE DRAWINGS. 8. THE WORK SHALL INCLUDE, BUT iS NOT NECESSARILY LIMITED T0. THE FOLLOWING: 1. ELECTRICAL DEMOLITION 2- NEW (480Y/27-M (208Y /12OVj, (ME] [SMF] PHASE, [FOUR) [THREE] WIRE ELECTRICAL SERVICE 3. NEW TELECOMMUNICATIONS SERVICE C SWITCHGfAR AND PANELBMROS 5. RACEWAYS 6. BUDDING WIRE AND CABLE 7. WIRING DEVICES 8. ELECTRICAL. BOXES AND FITNGS 9. CIRCUIT AND MOTOR DISCONNECTS 10. SUPPORTING DEVICES 11. SEISMIC RESTRAINTS 12. ELECTRICAL DENiOFICATION 13. GROUNDING 14. LIGHTING 15. CONDUIT FOR TELECOMMUNICATION SYSTEMS 16. WIRING FOR DIVISION 15 EQUIPMENT 17. FIRE ALARM SYSTEM WORK BY OTHERS A THE FOLLOWING WORK RELATED TO WORK UNDER THIS LXVISION OF THE SPECIFICATIONS WILL BE PRODDED BY OTHERS: 1. HEATING VENTILATING, AIR CONDITIONING AND PLUMBING EQUIPMENT, INCLUDING MOTORS, MOTOR STARTERS AND CONTROL EQUIPMENT WILL BE FURNISHED AND INSTALLED UNDER DIVISION 15. 2. PANTING, EXCEPT REPAIR OF FACTORY APPLIED FINISHES ON ELECTRICAL EQUIPMENT. 3. TELECOM SYSTEMS PRENIISES WRING AND ASSOCIATED SERVICE EQUIPMENT EXCLUDING EQUIPMENT REQUIRED 13Y LOCAL. SERVICE PROVIDER(S) FOR SERVICE ENTRANCE INTO FACLiY. CODES AND PERMITS A ALL WORK UNDER DIVISION 16 SHALL BE INSTALLED N ACCORDANCE WITH TIE REQUIREMENTS Of THE 2002 W[TION OF THE NATIONAL. ELECTRICAL CODE, AND THE LATEST EDITION OF ALL LOCAL OR STATE CODES, LAWS, AND ORDINANCES. AND THE REQUIREMENTS OF THE LOCAL. ELECTRIC UTiLITY. S. THIS CONTRACTOR SHALT. APPLY FOR, OBTAIN, AND PAY FOR ALL PERMITS REQUIRED. AT THE CONCLUSION OF THE INSTALLATION, HE OR SEE SHALL SECURE A CERTIFICATE OF INSPECTION, PROPERLY SIGNED BY THE CONTROLLING BUILDING DEPARTMENT, WHICH SHALL STATE THAT ALL RUES HAVE BEEN OOMPUED WITH AND THAT THE WORK IS SATISFACTORY. C. SHOED ANY PART OF THE PLANS OR SPECIFICATIONS BE FOUND TO BE N CONFLICT WITH APPLICABLE CODES OR ORDINANCES, THE CONTRACTOR STALL NOTIFY THE ENGINEER BEFORE SUBMITTING HIS OR HER DID. TRADE NAMES AND EQUALS A MANUFACTURER'S TRADE NAMES OR CATALOG NUMBERS USED N THESE SPECIFICATIONS AND INDICATED ON THE DRAWINGS DENOTE TYPE. SIZE. QUALITY, AND DESIGN OF EQUIPMENT REQUIRED. B. WHERE EQUIPMENT S SPECIFIED AS 'EQUA_', OR !APPROVED EQUAL', IT SHWA MEAN EQUAL N THE OPINION OF THE ENGINEER. THIS CONTRACTOR IS FREE TO OFFER SUBSTITUD NNS FOR CONSIDERATION AS EQUAL AFTER THE CONTRACT IS SIGNED; HOWEVER, HE SHALL BE PREPARED TO FURNISH SPECIFIED MATERIALS WHERE SUBSTITUTIONS ARE NOT APPROVED. MATERIAL AND EQUIPMENT A ALL MATERIALS AND EQUIPMENT SHAD BE NEW AND OF THE QUALITY SPECIFIED. B. MATERIAL OR EQUIPMENT THAT HAS BEEN STORED OUTDOORS UNPROTECTED FOR LONG PERIODS OF TIME OR OTHERWISE DAMAGED IS NOT ACCEPTABLE AS NEW MATERIAL. CC, APPARATUS AND MATERIALS USED N THIS WORK WHICH ARE SUBJECT TO APPROVAL OF UNDERWiRITERS LABOWORIES (UAL) SHALL BEAR THE UL ABEL, OR BE UNDERWRITERS LISTED. DELIVERY. STORAGE. AND HANDLING OF MATERIAL AND EQUIPMENT A THE CONTRACTOR SHALL BE RESPONSIBLE FOR THE PURCHASE. DELIVERY, AND STORAGE OF ALL MATERIALS AND EQUIPMENT INDICATED TO BE SUPPLIED UNDER THIS SECTION OF THE SPECFIATIONS. AND IT SERI BE HIS OR HER RESPONSIBILITY TO SCHEDIN.E THE DELIVERY OF MATERIALS AND EQUIPMENT AT SUCH STAGES OF THE WORK AS WILL PERMIT UNINTERRUPTED CONSTRUCTION OF ALL PHASES OF THE WORK. B. WHERE OWNER FURNISHED EQUIPMENT IS TO BE TURNED OVER TO THIS CONTRACTOR FOR iNSTAIATON, R SHALL BE THE RESPONSIBILITY OF THIS CONTRACTOR TO RECEIVE SUCH EQUIPMENT AND STORE N A SAFE, DRY LOCATION. C. THIS CONTRACTOR SHALL DO AL REQUIRED RKOGNG, HOSTING TRANSPORTING, ETC., OF ALL EQUIPMENT FURNISHED UNDER THIS CONTRACT, AND SHALL FURTHER F 04M ANY ADMIOJAL STRUCTURAL MEMBERS, AS MAY BE REQUIRED, FOR THE PROPER SUPPORT Of ANY AND ALL EQUIPMENT FURNISHED HEREUNDER. ACCURACY OF DATA A THE DRAWINGS ARE GENERALLY DIAGRAMMATIC. AND EXCEPT WHERE DIMENSIONS ARE SHOWN, ARE NOT INTENDED TO SHOW THE EXACT LOCATIONS OF OU TIM CONDUITS, SWITCHES, FIXTURES, ETC. ALL WORK SHALL BE INSTALLED AS NEARLY AS POSSIBLE IN THE LOCATIONS INDICATED. WITH ONLY SUCH MINOR ADJUSTMENTS AS WILL BE REQUIRED TO AVOID INTERFERENCES WITH STRUCTURE OR THE WORK OF OTHER TRADES. B. SHOED ANY STRUCTURAL OR MECHANi CAI. INTERFEREiNCES PREVENT THE INSTALLATION OF OMIT. SETTING OF JUNCTION BOXES AND CABINETS, ARRANGEMENT Of LIGHTING FIXTURES AND METHOD Of SUSPENSION. ETC., N THE LOCATIONS NOTED ON THE DRAWN % TiE NECESSARY DEVIATIONS THEREFROM MUST BE MADE WITHOUT ADDITIONAL COST TO THE OWNER, WHERE RELOCATION IS NOT OVER FIVE (5) FEET FROM THE LOCATION SHOWN ON THE DRAWINGS. C. THE DRAWINGS ARE FURTHER NOT INTENDED TO SHOW ALL JUNCTION OR PULL BOXES, FITTINGS AND CONNECTIONS, AND DETAILS OF WOOL TO BE WE THIS CONTRACTOR SHALL SUPPLY ALL NECESSARY BOXES, FITTINGS, AND OONNECT 4 FOR COMPLETE INSTALLATION N A SATISFACTORY MANNER. D. ANY OFFSETS N CONDUIT REQUIRED OR NECESSARY TO AVOID WERFERENOPS WITH STRUCTURE, OR THE WORK OF OTHER TRADES, ETC.. SHALL. BE MADE AT NO ADDITIONAL COST TO THE OWNER E. REFER TO ARCHITECTURAL AND STRUCTURAL DRAWINGS FOR ALL DIMENSIONS OF BUILDING SPACES. F. THIS CONTRACTOR SHALL PREPARE SHOP DRAWING % AS NECESSARY, FOR HIS OR HER USE N COORDIATiNG THE WOW TO AVID INTERFERENCE. G. THE DRAWINGS AND SPECIFICATIONS ARE COMPLEMENTARY TO EACH OTHER, AND WHAT IS CRIED FOR BY ONE SHALL BE AS BINDING AS F CALLED FOR BY BOTH. COORDINATION A THE ELECTRICAL CONTRACTOR SHAT COORDINATE HIS OR HER WORK WITH THAT OF OTHER SUBCONTRACTORS ON THE JOB AND ALSO WITH THAT OF THE OWNER N ORDER THAT THERE BE NO DELAY N THE PROPER INSiALATION AND COMPLETION OF THE SEVERAL PARTS OF THE WORK. B. THIS CONTRACTOR SHALL USE EVERY PRECAUTION TO PROTECT TiE WORK OF OTHERS, AND HE WILL BE HELD RESPONSIBLE FOR ALL DAMAGE OONE BY HIS OR HER WORKERS TO THE WORK OF OTHER TRADES. HE OR SHE SHALL ALSO PROTECT HIS OR HER WDRK FROM DANGER OF BREAKAGE, DIRT, TOM MATERIALS, ETC., AND SHWA. REPLACE ALL WORK SO DAMAGED. C. COORDINATE PHASES OF THE WORK WITH THE OWNER AND OTHER TRADES TO ALLOW THE OWNER TO CONFTINIE NORMAL BUSINESS OPERATIONS THROUGHOUT THE DURATION OF THE PROJECT. ANY NECESSARY POWER OUTAGES SHALL BE SCHEDULED FOR OTHER TAN THE OWNER'S HOURS OF OPERATION, OR BE PRE - ARRANGED WITH THE OWNER. MANUFACTURER'S RECOMMENNDATIONS A UNLESS SPECIFICALLY NDICATED OTHERWISE, ALL EQUIPMENT AND MATERIALS SHALL BE INSTALLED N ACCORDANCE WITH THE BEST RECOMMENDATION OF THE MANUFACTURER. A COPY OF THE MANUFACTURER'S INSTALLATION RECOMMENDATIONS SHALL BE KEPT IN THE JOB SUPERINTENDENT'S OFFICE AND SEOUL BE AVAILABLE TO THE OWNER'S REPRESENTATIVE AT ALL TIMES. CUTTING AND PATCHING A. THiS CONTRACTOR SHALL BE RESPONSiBL.E FOR ALL CUTTING AND PATCHING REQUIRED FOR THE INSTALLATION OF HIS WORK, AND HE SHALT. EMPLOY WORKERS SKILLED IN THE TRADES REQUIRED FOR ALL CUTTING AND PATCHING WORK. B. THIS CONTRACTOR SHALL BE RESPONSIBLE FOR THE PROPER LOCATION OF ALL CHASES, RECESSES, AND OPENINGS REQUIRED FOR HiS WORK. G THIS CONTRACTOR SAL PROVIDE AL SLEEVES, ETC., REQUIRED FOR THE INTRODUCTION AND PLACEMENT OF HIS WORK, AND SHALL BE RESPONSIBLE FOR THE CORRECT LOCATION OF SAME. 0. BEAMS OR COLUMNS SHALL NOT BE PIERCED WITHOUT PERMISSION OF THE STRUCTURAL ENGINEER, AND THEN ONLY AS DIRECTED. PROTECTION OF FLOORS A THIS CONiKTOWS ATTENTION IS DIRECTED TO THE NEED TO PROTECT FINISHED FLOORS, AND HE OR SHE WILL BE HELD RESPONSIBLE FOR DAMAGE HE OR SHE MAY DO TO FiHNSHED FLOORS, WHERE HEAVY EQUIPMENT iS TO BE MOVED ACROSS FINISHED FLOORS, THIS CONTRACTOR SHALT. MAKE PROVISIONS TO PROTECT THE FLOOR. B. WHERE PIPE CUTTINGS AND THREADING OPERATIONS ARE CARRIED ON BY THIS CONTRACTOR, HE OR SHE SHALL PROVIDE A SUITABLE COVERING MATERIAL OVER THE FLOOR WHICH WILL ASSURE THAT OIL AND PIPE CUTTINGS DO NOT COME IN CONTACT WITH THE FINISHED FLOOR. TEMPORARY FLOOR COVERING SHALL. BE PLYWOOD OR OTHER MATERIALS AS MAY BE APPROVED BY THE ENGINEER. C. THIS CONTRACTOR SHALT. REMOVE ALL TEMPORARY FLOOR COVERING, AS HE OR SHE COMPLETES HiS OR HER WORK IN EACH AREA ANY QAMAGE RESULTING FROM ACTIVITIES OF THiS CONTRACTOR SHAD. BE REPAIRED AT HIS OR HER OWN EXPENSE. PAINTING A THE ELECTRICAL CONTRACTOR SHALL REFINISH AND RESTORE TO THE ORIGINAL CONDITION AND APPEARANCE, ALL ELECTRICAL. EQUIPMENT WHICH HAS SUSTAINED DAMAGE TO MANUFACTURER'S FINISH PANT FINISHES SHALL INCLUDE GALVANIZING THAT PAS BEEN REMOVED DURING INSTALLATION. B. ALL ELECTRICAL EQUIPMENT SHALL BE PROVIDED WITH FACTORY APPLIED PRIME AND FINISH PAINT. UNLESS OTHERWISE SPECIFIED. SHOP DRAWINGS (MM A SDI COPIES OF SHOP DRAWINGS AND /OR MANUFACTURER'S DESCRIPTIVE DATA OF A NATURE TO OOMPLERY SEIM THE EQUAIFf OF THE MATERIAL OR EQUIPMENT INTENDED FOR INSTALLATION SHALL BE 92MIffED FOR APPROVAL. BEFORE BEGINNING ANY CONSTRUCTION AND "IN THPiY DAYS AFTER SIGNING CONTRACT. FAILURE TO SUBMIT DATA FOR APPROVAL WITHIN THIRTY DAYS THE LIMIT WILL BE CONSTRUED AS MEANING EQUIPMENT CAVED FOR BY NAME WILL BE FURNISHED. DATA SHALL BE ORGANIZED IN SAME ORDER AS LISTED BELOiM. SHALL BE SLWIJED ALL IN ONE THREE RING BINDER, INDDCED BY FLYSHEET ON FRONT PAGE, EACH ITEM TABBED AND LABELED, ARRANGED IN THE ORDER DO APPEAR IN THE SPECIFICATIONS. AND BE BOUND N SETS, ALL SETS IDEMHCAL. NO EXCEPTION WILL BE MADE TO THIS PROCEDURE AND TIMIE SCHWE B. EACH ITEM SUBMITTED FOR REVIEW SHALL HAVE SUBMITTAL DATA PRECEDED BY A TYPEWRITTEN DESCRIPTION (BY CONTRACTOR OR ITEM SUPPLER) OF THE ITEM. DESCRIPTION TO INCLUDE MAKE AND MODEL NUMBERS AND SHALL DESCRIBE THE ITEM. LiST ALL OPTIONS AND ACCESSORIES SHOWN ON SHOP DRAWINGS WHICH ARE NOT INCLUDED. SUBMIT THE FOLLOWING FOR APPROVAL.• 1. RACEWAYS 2. WIRES AND CABLES I ELECTRICAL BOXES 4. WIRE CONNECTION AND CONNECTING DEVICES 5. WIRING DEVICES 6. CIRCUIT/MOTOR DISCONNECTS 7. PAE LBOARDS & OVER(XRRENT PROTECTIVE DEVICES 9. CONTACTORS AND LOTTING C(NfTRO. EQUIPMENT 10. LAMPS. BALLASTS. AND LIGHTING FDQURES 11. GENERATOR 12. TRANSFER SWITCH 11 LIGHTNING PROTECTION SYSTEM 14. FIRE ALARM C. CONTRACTOR SHWA SUBMIT 1/4' SCALED PLANS OF EACH ELECTRICAL ROOM DEPICTING THE LOCATION AND ARRANGEMENT OF ALL ELECTRICAL EQUIPMENT. RECORD DRAWINGS A THIS CONTRACTOR SHIN. MANTAIN A COMPLETE UP- TO-DATE SET OF RECORD DRAWINGS AND SPECIFICATIONS ON THE JOB SITE DRAWINGS SHALT. BE MAINTAINED IN A NEAT CONDITION AND SHALL CLEARLY SHOW ANY CHANGES FROM ORIGINAL DRAWINGS AND SPECIFICATIONS. B. CONTRACTOR SHALL USE A DESIGNATED SET OF PRINTS OF THE CONTRACT DOCUMENTS, AS PREPARED BY THE ENGINEER, TO MARK UP FOR RECORD DRAWING PURPOSES. C. THE CONTRACTOR SHALT. PREPARE A SET OF REPRODUCIBLE RECORD DRAWINGS. iHESE DRAWINGS AND A SET OR SPECIFICATIONS SHALL BE TURNED OVER TO THE OWNER AND SHALL BECOME THE PROPERTY OF THE OWNER BEFORE FINAL PAYMENT WILL BE MADE. MAINTENANCE MANUALS A CONTRACTOR SHALL PROVIDE THREE (3) COPIES OF OPERATIONAL AND MAINTENANCE MANUALS FOR ALL EQUIPMENT INSTALLED UNDER THIS DMSiON OF THE SPECIFICATIONS. THE MANUALS SHAT INCLUDE A LIST OF SPARE PARTS AND PROPER OPERATIONAL AND MAINTENANCE PROCEDURES. B. THE MANUALS SHALL BE ORGANIZED AND FULLY INDEXED MANUALS SHWA CONSIST OF THREE -RING, HARD BACK BINDERS WiTH APPROPRIATE DIVIDERS FOR EACH PART. C. MANUAL CONTENTS SHALL INCLUDE. BUT SHALL NOT BE LIMITED TO THE FOLLOWING: 1. NAME AND ADDRESS OF CONTRACTOR, EQUIPMENT MANUFACTURER AND SUPPLIER I SET OF APPROVED SHOP DRAWINGS OR APPROVED SUBMITTAL DATA 3. WRING DIAGRAMS AND INSTALLATION DRAWINGS 4. SPARE PARTS AND REPLACEMENT PARTS LISTS AS RECOMMENDED BY THE MANUFACTURER 5. PROPER OPERATIONAL PROCEDURES AND MAINii:NANCE PROCEDURES 6. INSTALLATION AND OPERATIONAL MAMAS 7. MAINTENANCE AND SERVICE MANUALS & COPY OF WARRANTIES AND GUARANTEES D. OPERATING AND MAINTENANCE MANUALS SHALL BE TURNED OVER TO THE OWNER BEFORE FINAL PAYMENT WILL BE MADE. E IT SHALL BE THE RESPONSIBILITY OF THIS OMTRACTOR TO MAINTAIN. WARRANT. CLEAN. ETC., ANY EQUIPMENT SUPPLIED BY THIS CONTRACTOR UNTIL ALL INSTALLATION AND OPERATING AND MAINTENANCE MANUALS ARE TURNED OVER TO THE OWNER. TEMPORARY CONSTRUCTION POWER AND LIGHTING A THIS CONTRACTOR SHAI FURNISH AND INSTALL ALL TEMPORARY WIRING FOR CONSTRUCTION POWER AND LIGHTING FOR THE PROJECT AS (REQUIRED. B. A TEMPORARY ELECTRICAL SERVICE, F REQUIRED, FOR CONSTRUCTION POWER AND LIGHTING SHALI. BE OBTAINED BY THIS CONTRACTOR N THE NAME Of THE 000. WHO WILL PAY ALL POWER AND ENERGY CHARGES. ANY COST FOR THE TEMPORARY SERVICE CONNECTION SHALL BE PAD BY THIS CONTRACTOR. m A THE ENTIRE BUILDING WIRING SYSTEM SHALL BE THOROUGHLY TESTED AND CORRECTED OF ALL DEFECTS. ALL ELECTRICAL WIRING SILL BE TESTED FOR CONTINUITY, SHORTS. IMPROPER GROUNDS AND INSUATiON RESISTANCE. MOTORS SH A I BE CHECKED FOR PROPER ROTATION AND BRANCH CIRCUIT AND OVERLOAD PROTECTION. PANELBOARDS SHALL BE CHECKED FOR BALANCED LOADING AND CORRECT PHASE ROTATION. ALL DISCREPANCIES SHALL. BE CORRECTED. INS CONTRACTOR SHALL. FURNISH TEST EQUIPMENT AND MATERIAL, AND SHALL BE RESPONSIBLE FOR REPLACEMENT OR REPAIR OF DAMAGE DUE TO TEST FAILURES. 8. 90 INSTALLATION IS COMPLETE, VOLTAGE MEASUREMENTS SHALL BE MADE AT EACH PANEL80ARD TO VERIFY PROPER SYSTEM VOLTAGES, VOLTAGE SHWI BE MEASURED UNDER LOAD CONDITIONS WHERE POSSIBLE. VOLTAGE READINGS SHAT BE RECORDED. C. AFTER ALL TESTS HAVE BEEN COMPLETED, THIS CONTRACTOR SHWL CLEAN ALL THE FIXTURES AND REPLACE AMY LAMPS USED FOR TEMPORARY LIGHTING. ALL EQUIPMENT AND CONDUIT SHALL. BE CLEANED AND LEFT N WORKING ORDER. ALL DEBRIS CREATED BY THE EXECUTION OF THE ELECTRICAL WORK SHALL BE REMOVED BY THIS CONTRACTOR THiS CONTRACTOR SHALL TAKE ALL NECESSARY PRECAUTIONS TO KEEP PANELS, ESPECIALLY CIRCUIT BREAKER HANDLES, CLEAN DURING CONSTRUCTION. 0. CHECK ALL OONTROI AND INTERLOCKING WIRING FOR PROPER OPERATIONS. PERFORM OPERATIONAL TESTS TO ASSURE THAT CONTROL WIRING WAS BEEN PROPERLY INSTALLED. E. PRIOR TO FINAL ACCEPTANCE, CONTRACTOR SHALL PROVIDE ALL TEST RESULTS TO ENSURE THAT SYSTEM IS FREE OF DEFECTS AND FULLY OPERATIONAL. GUARANTEE A THE CONTRACTOR SHALT. GUARANTEE TO THE OWNER ALL WORK PERFORMED UNDER THIS CONTRACT TO BE FREE FROM DEFECTS N WORKMANSHIP AND MATERIAL FOR A PERIOD OF ONE (1) YEAR FROM DATE OF FINAL AOEPTAMCE. DEFECTS ARISING DURING THIS PERIOD WILL BE PROMPTLY REMEDIED BY THE CONTRACTOR AT HIS OR HER OWN EXPENSE UPON NOTICE BY THE OWNER ALL LAMPS FOR LIGHTING FIXitRES SHWA BE EXCLUDED FROM THiS GUARANTEE, BUT ONE (1) COMPLETE AND OPERATIVE SET OF LAMES FOR LIGHTiNG FIXTURES SHALL BE N PLACE AT THE TiME OF FINAL A(XEPIANCE. SITE WORK A BEFORE STARTING EXCAVATION, ESTMUSH THE LOCATION OF UNDERGROUND AND OVERHEAD UTILITIES N THE WORK AREA. EXERCISE CARE TO PROTECT EXISTING UTIUTiTES DURING EARTHWORK OPERATIONS. PERFORM EXCAVATION WORK NEAR UTILITIES BY HAND AND PROVIDE NECESSARY SHORING. SHEETING, AND SUPPORTS AS THE WORK PROGRESSES. B. MAINTAIN, PROTECT, RELOCATE, OR EXTEND AS REQUIRED EXISTING UTILITY LINES TO REMAIN WHICH PASS THROUGH THE WORK AREA C. N COORDINATION WITH LOCAL ORDINANCES, REMOVE ABANDONED UTILITY SERVICE LINES FROM AREAS OF EXCAVATION. F DISCOVERED CAP, PLUG OR SEAL ABANDONED LINES AND IDENTIFY TERMINATION POINTS AT GRADE LEVEL WiTH MARKERS. 0. BACKFLL TRENCHES ONLY AFTER CONDUITS HAVE BEEN INSPECTED AND THE LOCATIONS OF CONDUITS HAVE 80 RECORDED ON AS -BULT DRAWINGS. E AFTER CONDUT HAS BEEN LAID AND JOINTED, THE CONDUIT SHALL BE BEDDED N THE TRENCH AND MADE SECURE AGAINST MOVEMENT BY SACKFIWNG THE TRENCH BY HAND WiTH 3/4' WASHED GRAVEL OR SAND TO A DEPTH OF 12' ABOVE THE TOP OF THE CONDUIT. ALL SCHEDULE 40 PVC CONDUIT SHALL BE ENCASED N A 3' CONCRETE ENVELOPE. F. BACKFILI. REiMAINING DEPTH WITH EXCAVATED MATERIAL. EXCEPT THAT THE MATERIAL TAY 044 STONES, ROCKS, CONCRETE, OR MASONRY MATERIALS (BUT NO CINDERS} WITH A MAXIMUM DIMENSION OF FOR (4) INCHES PROVIDED THAT THE VOIDS N SUCH COARSE MATERIALS ARE COMPLETELY FILLED WITH EARTH OR GRANULAR MATERRW.. G. THOROUGHLY COMPACT BACKFIL BY TAMPING WITH A MANUAL TAMP OR AN APPROVED MECHANICAL LIMPING DEVICE H. WHERE PLACEMENT OF UNDERGROUND CONDUIT DISTURBS PAVED AREAS, THE PAYMMENT SHALL BE REPAIRED WITH MATERIALS OF THE SAME TYPE AND STRENGTH AS THAT REMOVED. RACEWAYS A ALL WIRING SHALL BE INSTATED N A CONTINUOUS RACEWAY SYSTEM, OR TYPE MC CABLE AS ALLOWED E1_TNHFRE N THESE SPECIFICATIONS. CONDUIT SHALL BE RUN CONGEALED OR On". AS SPECIFICALLY INDICATED ON THE PLANS. IN GENERAL. CONDUIT S INDICATED TO BE RUN CONCEALED N FINISHED AREAS; ALL OTHER CONDUIT IS RUN EXPOSED. 8. ELECTRICAL METALLIC TUBING (00 MAY BE USED WHERE CONDUIT S RUN CONGEALED IN WALLS ABODE THE FLOOR SUB AND ABOVE OFFICE SPACES. GRS SHALL BE USED WHERE CONDUITS ARE RUN EXPOSED INSIDE THE BUILDINGS UP TO 6' AFF. EXPOSED CONDUIT ABOVE 6' AFT SHALL BE EMT (UNLESS OTHERWISE NOTED). C. GALVANIZED RIGID STEEL CONDUIT OR SCHEDULE 40 WC CONDUIT SHALL BE USED UNDERGROUND AND WHERE ON IT IS RUN UNDER THE FLOOR SLAB. GALVANIZED RIGID STEEL ELBOWS SHALL BE USED N ALL PVC CONDUIT RUNS AND WHERE O ITS ARE STUBBED UP THROUGH FLOOR SLABS. GALVANIZED RIGID STEEL CONDUIT, OR NiERMEDATE MEW CONDUIT SHALL BE USED WHERE CONDUIT PROJECTS ABOVE THE ROOF, WHERE CXNNDUIf IS SUBJECT TO PHYSICAL DAM AGE. AND ALL OTHER LOCATIONS SPECIFICALLY DESIGNATED ON THE DRAWINGS OR RREQUPED BY THE SPECIFICATIONS. 0. INTERMEDIATE STEEL CONDUIT MAY BE USED N LIEU OF GALVANIZED RIGID STEEL CONDUIT, WHERE PERMITTED BY CODE. E. LIQUID -TIGHT FLEXIBLE METAL CONDUIT N SHORT LENGTHS (30' OR LESS) SHAD BE USED AT WKCT06 TO MOTORS, OR TO EQUIPMENT SUBJECT TO MOVEMENT, YCRATXON OR MISALGNMENL LIQUID -TIGHT FLEXIBLE CONDUIT SHALL NOT BE USED FOR OTHER APPLICATIONS. F. CONTRACTOR MAY PROVIDE TYPE MIC CABLE IN LIEU OF EMf CONDUIT OR FLEXIBLE METAL CXNNDUIT CONCEALED N WALLS OR CEILINGS FOR LIGHTING AND RECEPTACLE CIRCUITS DO NOT USE TYPE MC GABLE FOR FiRE HARM, WAG EQUIPMENT, N EXPOSED LOCATIONS, OUTDOORS, OR FOR CIRCUITS LARGER THAN 20 AMPS G. EXPOSED CONDUIT SHALL BE RUN IN PARALLEL ROWS NEATLY RACKED PARALLEL OR PERPHNOICUAR TO WALLS AND STRUCTURAL MEMBERS. H. INSTALL. CONDUIT ONLY AFTER PROPOSED RUNS WINE BEEN CHECKED ON PANS AND AT SITE FOR INTERFERENCE WITH OTHER TRADES. WHEREVER POSSIBLE. LOCATE CONDUIT OVER PANG OF OTHER TRADES. ALL HORIZONTAL CONDUIT RUNS N ATTIC SHALL BE RUN AS HIGH AS POSSIBLE N ORDER TO PROVIDE FREE SPACE ABOVE CEILING FOR INSTALLATION OF AIR DISTRIBUTION DUCT AND PIPING. 1. RWCHING -N DIMENSIONS OF ELECTRICALLY OPERATED EQUIPMENT WILL BE BY TRADES SUPPLYING SAME. SET CONDUIT AND BOXES FOR CONNECTING TO EQUIPMENT ONLY AFTER RECEIVING APPROVED DIMENSIONS AND LATER CHECKING LOCATIONS WITH OTHER CONTRACTORS. J. PLUG THE ENDS OF EACH RACEWAY WITH AN APPROVED CAP, OR CAPPED BUSHING TO PREVENT THE ENTRANCES OF FOREIGN MATERIAL DURING THE CONSTRUCTION PERIOD. CONDUIT LEFT EMPTY FOR FUTURE WIRING SHALT. BE CAPPED. K. ARRANGEMENTS OF CONDUIT MIRING AND EQUIPMENT THAT DIFFER MATERIALLY FROM THE OBVIOUS NOT OF THE PLANS WILL NOT BE PERMITTED, EXCEPT WHERE NECESSARY TO AV'010 INWERENGES AND ONLY WHERE SPECFC?LLY APPROVED BY THE ENGINEER L OMDUIT SHALT. BE SIZED AS INDICATED ON THE PLANS AND WHERE NOT INDICATED, SIZES SHALL MEET NEC RREQURQMENiS FOR NUMBER OF CONDUCTORS TO BE ACCOMMODATED, BASED ON TYPE TIHN INSULATED CONDUCTORS. M. CONDUITS PROJECTING THROUGH ROOFING SHALL BE MADE WATERTIGHT BY PROPER FLASHING AND PITCH POCKETS WITH STORM COLLAR SECURELY FASTENED TO CONDUIT ABOVE RE FLASHING N. SHORT LENGTHS OF FLEXIBLE STEEL. CODUi, 'CREfNFELD', MAY BE USED ADM FURRED CEILINGS BETWEEN OUTLET BOXES AND LAY-IN TYPE CEILING FIXTURES. 0. ELECTRICAL METALLIC TUBING 3/4' AND LARGER SHWL BE PROVIDED WITH INSULATED CONNECTORS OR END BUSHINGS. P. MINIMUM 51ZE BRANCH CIRCUIT COWUIT SHAT BE 1/2' NOMINAL SIZE. Q. ALL RIGID AND AMC WOO COUPLINGS, FITTINGS AND CONNECTORS SHALL BE WADED TYPE. R. WHERE THE CONTRACTOR ELECTS TO USE OTHER RIGID STEEL CONDUIT OR IMC CONDUIT, HE OR SHE SHWA USE ONE OR THE OTHER THROUGHOUT THE PROJECT. DO NOT MIDI RIGID STEEL AND AMC CONDUIT. S. ALL OPENINGS WHERE CONDUIT PENETRATES WALLS OR FLOORS SHALL BE SEALED WATER AND AIRTIGHT. T. CONNECTORS AND COUPLINGS FOR EMT CONDUIT IN WET OR OAMP LOCATIONS SHWA BE COMPRESSION TYPE, EMT FITTINGS MAY BE DIE--CAST METAL OR STEEL U. ALL CONDUIT SHALL BE UL LISTED AND LABELED FOR THE APPLICATION USED. V. WHERE THE USE OF PVC CONDUIT IS INDICATED, ALL JOINTS SHALL BE SOLVENT WELDED WITH CEMENT FURNISHED BY THE CONDUIT MHAlUFACTURTR PROVIDE SUITABLE ADAPTERS WHERE PVC CM0 ARE COUPLED TO METALLIC CXNDUITS. ALL ELBOWS SHALL BE MADE OF GALVANIZED FOGS STEEL CONDUIT. W. ALL PNC CONDUITS INSTALLED BELOW GRADE SHWA. BE DNC M N A 3' CONCRETE ENVELOPE. X. ALL CONDUIT BELOW SLAB ON GRADE SHALL BE PVC AND SHALL BE INSTATED A MINIMUM OF i'-0" BELOW SLAB. ALL SLAB PENETRATIONS SHALL BE MADE OF GALVANIZED WD STEEL BUILDING WARE. CABLE. AND CONNECTORS A BUILDING WIRE AND CONNECTORS SHAT BE UL LISTED AND LABELED. COMPLY WiTH NEiAA, ICE& ANSI AND ASTM STANDARDS PERTAINING TO MATERIALS, CONSTRUCTION AND TESTING OF BUILDING WiRE AND CABLE. B. EXCEPT AS OTHERWISE NDICATED, PROVIDE WIRE, CABLE AND OONMECTORS OF MANUFACTURER'S STANDARD MATERIALS, AS IDiCATED BY PUBLISHED PRODUCT INFORMATION, DESIGNED AND CONSTRUCTED AS RECOMMENDED BY MANUFACTURER AND AS REQUIRED FOR THE INSTALLATION. C. PROVIDE FACTORY FA "ED 600 VOLT INSULATED BUILDING WIRE OF SIZES, RATINGS, MATERW.S, AND TYPES INDICATED BELOW: UL TYPE: THHN/1HWN MATERIAL. COPPER CONDUCTORS: j10 AWG AND SKIM SOLD OR STRANDED CONDUCTORS: 18 AWG AND LARGIF'R CONCENTRIC- LAY - STRANDED (STANDARD FIEXIBNITi') D. CONDUCTOR DENTFICATKOt CONDUCTORS SHWl BL IDENTFED BY COLOR AS FOLLOWS 203Y/120 480Y/277 VOLT SYSTEMS VOLT SYSTEMS A PHASE BLACK BROWN a PHASE RED ORANGE C PHASE BLUE YELLOW NEUTRAL. WHiTE CRAY EQUIPMENT GROUND GREEN GREEN MATED GROUND GtEQ4 W/ YELLOW STRIPE E. COLOR FOR CONDUCTORS 110 AWG AND SMALLER SHWA BE PERMANENT FACTORY APPLIED. CONDUCTORS 18 AWG AND LARGER SHAM. BE BLACK COLOR COOED PRISE TAPE APPLIED AT THE TERMINATIONS. WHERE TYPE MC CABLE IS USED, CIRCUIT NUMBERS SHALT. BE APPLIED AT ALL WIRE SPLICES AND TERMIATKONS. F. NSiALL ELECTRICAL BOLDING WIRES AND CABLES, AS NOTED, IN COMPLIANCE WITH MANUFACTURER'S WRITTEN INSTRUCTIONS. APPLICABLE REQUIREMENTS OF NEC, AND IN ACCORDANCE WITH RECOGNIZED INDUSTRY PRACTICES. G. WIRE SHALL BE PROTECTED DURING STORAGE AND HANDLING AND %IAL. BE N FIRST CLASS CONDITION WHEN INSTALLED. K NO GREASE OF ANY KiND AND NO COMPOUND OTHER THAN A NEUTRAL LUORICANT AS APPROVED BY THE WIRE OR CABLE MANUFACTURER SHALL BE USED AS A RUM COMPOUND. L WHEN WIRES ARE INSTALLED IN CONDUIT, SUFFICIENT SLACK SUL BE ALLOWED TO PERMIT THE CONNECTION OF FIXTURES OR WIRING DEVICES WITHOUT ADDITIONAL SPL.IE. J. ALL CONDUCTORS SFNLI BE CONTINUOUS FROM OUTLET TO OUTLET OR FROM PANEL TO OUTLET OR DEVICE. NO SPLICES WLLBE PERMITTED IN CONDUIT RUINS. K. FEEDERS SHALL BE RUN N INDIVIDUAL CONDUITS FROM THE FEEDER SOURCE TO THE LOA) TERMINATIONS, AS INDICATED ON THE DRAWINGS. DO NOT COMBINE MULTIPLE FEEDERS IN A WIREWAY OR JUNCTION BOX. L USE COMPRESSION TYPE WIRE CONNECTORS FOR STRANDED CONDUCTORS, FOR MOTOR CONNECTIONS, AND Al OTHER CONNECTIONS OR SPLICES SUBJECT TO VIBRATION. WIRE HUTS MAY BE USED ELSEWHERE. M. BRANCH CIRUM FOR MOTORS, AS NDiOATED ON THE DRAWINGS, ARE APPROXIMATE SIZE ONLY. THiS CONTRACTOR IS CAUTIONED TO OBTAIN THE EXACT RATING OF THE MOTOR OPERATED EQUIPMENT FROM THE MECHANICAL CONTRACTOR, AND HE OR SHE SHALL Wig THE SIZE OF THE PROTECTIVE DEVICE AND WIRE TO CONFORM TO THE REQUIREIMEMS OF THE EQUIPMENT. ALL SUCH CHANGES SHWA BE SUBMITTED TO THE ENGINEER FOR APPROVAL. K AT EACH OUTLET LOCATION. THE TERMINATING CONDUCTORS SHALL BE LEFT NOT LESS TAN 8" LONG WITHIN THE OUTLETS, 0. USE PULLING MEANS, INCLUDING FiSH TAPE, CABLE, OR ROPE WHICH CANNOT DAMAGE RACEWAY. P. TORQUE ALL BOLTED LUGS AND CONNECTORS TO TORQUE AUES RECOMMENDED BY THE EQUIPMENT MANUFACTURER. WHERE TORQUE VALUES ARE NOT GIVEN, USE APPLICABLE TORQUE VALUES GIVEN BY UL STANDARDS 1486A AND 14868. Q. AS FAR AS POSSiBL.E. CONDUCTORS SHALL BE PULLED THROUGH WITHOUT SPLKE. WHERE SPLICES ARE NECESSARY AND APPROVED BY THE ENNGNEER, THEY SHALL BE MADE IN JUNCTION OR PULL BOXES ONLY R. MINIMUM SIZE BRANCH CIRCUIT CONDUCTOR SHALL BE J12 AWG. S. FEED CONNECTIONS AT PMELBOAROS SHALL PROVIDE THE PROPER Mk% RELATIONSHIP, AS INDICATED ON THE DRAWINGS, OR AS SPECIFIED HEREIN, BOXES AND FITTINGS A N GENERAL, APPLICATION OF ELECTRICAL. BOX AND ELECTRICAL. FITTING WORK IS INDICATED BY THE DRAWINGS, SCHEDULES AND THESE SPECIFiCATONS. PROVIDE ADDITIONAL ELECTRICAL BOXES AND FITTINGS AS MAY BE REQUIRED FOR A COMPLETE ELECTRICAL. INSTALLATION. B. TYPES OF ELECTRICAL. BOXES AND FITTINGS N THiS SECTION INCLUDE THE FOLLOWING: 1. OUTLET BOXES 2. JUNCTION BOXES 36 PILL. BOXES C CONDUIT BODIES 5. BUSHINGS 6. LOCK" 7. FLOOR BOXES 0 COMPLY WITH NEC AS APPLICABLE 10 CONSTRUCTION AND NSTALATION OF ELECTRICAL WRING BOXES AND FITTINGS. D PROVIDE ELECTRICAL. BOXES AND FITTINGS WHICH HAVE BEEN UL LISTED AND LABELED AND COMPLY WITH THE FOLLOWING STANDARDS: 1. STANDARD NO. 50: ELECTRICAL CABINETS AND BOXES 2. ANSI C 134.1 SHEET STEEL OUTLET BOXES, DEVICE BOXES, COVERS AND BOX SUPPORTS. E PROVIDE GALVANIZED PRESSED sTEEI INTERIOR OUTLET WiRING COXES, OP TYPES, SHAPES, AND SIZES, INCLUDING BOX DEPTHS, TO SUIT EACH RESPECTIVE LOCATION AND INSTALLATION, AD WITH THREADED SCREW HOLES WiTH CORROSION RESISTANT SCREWS FOR SECURING BOX COVERS AND WIRING DEVICES. F. PROVIDE OUTLET BOX ACCESSORIES AS REQUITED FOR EACH INSTALLATION, INCLUDING MOUNTING BRACKETS, WALL 80AR0 HANGERS, EXTENSION RINGS, FIXTURE STUDS, CAM CLAMPS, AND METAL STRAPS FOR SUPPORTING OUTLET BOXES, WHICH ARE COMPATIBLE WITH OUTLET BOXES BEING USED AND WHICH FULFIL. REQUIREMENTS OF ID(VDUL WIRING SITUATIONS. G. SUBJECT TO COMPLIANCE WITH REQUIREMENT% PROVIDE PRESSED STEEL OUTLET BOXES OF ONE OF THE FOLLOWING- 1. CROUSE -HINDS CO. 2. STEEL CITY K PROVIDE CORROSION RESISTANT CAST METAL OUTLET BOXES WiTH TREADED HUB CONDUIT ENDS, CROUSE -HINDS 'F' SERIES, OR APPROVED EQUAL L PROVIDE GALVANIZED CAST METAL CONDUIT BODIES OF TYPES, SHAPES AND SIZES TO SUIT RESPECTIVE LOCATIONS AND INSTALLATION. CONSTRUCT WITH TIRFAOED- CONDUIT- OTRANCE ENDS, REMOVABLE COVERS AND COW" RESISTANT SCREWS, APPLETON FORM 35 SERIES, OR APPROVED EQUAL. J. PROVIDE GALVANIZED OXDE GAUGE SHEET STEEL JUNCTION AND PULL BOXES WITH SCREW -ON COVERS AND WELDED SEAMS. DO NOT USE KNOCKOUT TYPE BOXES FOR ANY APPLICATION IN SIZES LAW THAN 4- 11116". K. PULL BOXES FOR STRAIGHT RUNS SHALL BE 0- 1/0-FO f TYPE P8, OR APPROVED EQUAL L PROVIDE CORROSION - RESISTANT PUNCHED -STEEL BOX KNOCKOUT CLOSURES, CONDUIT LOCKNUTS AND MALLEABLE IRON CONDUIT BUSHINGS, OFFSET CONNECTORS OF TYPES AND SIZES TO SUIT RESPECTIVE USE AND INSTALATKU BUSHINGS FOR ALL CONDUIT CONTAINING CONDUCTORS 13 AWG AND LARUHER SHALL BE INSULATED TYPE CONFORMING TO UL 514. M. BUSHINGS FOR OMIT TERMINATIONS, WHERE CONDUIT ENTERS OR EQUIPMENT FROM UNDERGROUND SHALL BE O- Z /GEDNEY CO., TYPE CS8 SERIES, OR APPROVED EQUAL. K INSTAL ELECTRICAL BOXES AND FITTINGS, WHERE INDICATED OR REQUIRED. COMPLYING WITH APPLICABLE REQUIREMENTS OF NEC AND NECA "STANDARD OF NSTALATIK AND IN COMPLIANCE WITH RECOGNRED INDUSTRY PRACTICES, TO ENSURE THAT PRODUCTS FULFILL REQUIREMENTS. O. PROVIDE KNOCKOUT' CLOSURES AT UNUSED KNOCKOUT HOLES WHERE BLANKS HAVE BEEN REMOVED, P. PROVIDE SEPARATE STRUCTURAL SUPPORTS FOR AL BOXES AND PULL BOXES N ACCORDANCE WiTH CODE REQUIREMENTS. Q. PROVIDE CAST METAL, WEATHERPROOF OUTLETS FOR LOCATIONS EXPOSED TO WEATHER OR MOISTURE. R. FLOOR BOXES SHALL BE CAST -IRON, FLUSH TYPE, WITH BRASS FLOOR INSETS, S. FOR EXPOSED WORK USE CAST META. BOXES WiTH S(YtEWED FAGS FOR ALL BRANCH CIRCUIT OUTLET, DEVICE AND PULL BOXES. T. TEMPORARY COVERS SHALL BE PROVIDED AT ALL OUTLET BOX LOCATIONS DURING CONSTRUCTION TO PREVENT ENTRANCE OF DIRT, PIASTER, ETC., BEFORE WIRING DEVICE IS INSTALLED. U. EXCEPT WHERE INDICATED OTHERWISE ON THE DRAWINGS, OUTLET BOXES SHALL BE SO LOCATED AS TO ALLOW THE ASSOCIATED DEVICE OR FAILURE TO BE MOUNTED AT LOCATIONS SPECIFIED BELOW: 1. CEILING LIGHTING MURES - SYMMETRICALLY N CEILING, OR AS NOTED ON THE PLAINS. 2. RECEPTACLES - 4' -0' ABOVE FLOOR N UTILITY ARK 1' -6' ABOVE FINISHED FLOOR EXCEPT WHERE INDICATED OTHERWISE. 3. WALL SWATCHES - 4'--0' ADM FINISHED FLOOR EXCEPT WHERE IDiCATED OTHERWISE 4. OUTLETS FOR TELEPHONE/DATA - SAME AS RECEPTACLES, EXCEPT WALL MOUNTED PHONE OUTLETS SFWI BE 4' -6' AFF. S. OUTLETS FOR OTHER DEVICES - AS INDICATED ON DRAWINGS. V. PROVIDE PUT. BOXES AND JUNCTION BOXES, AS INDICATED ON THE PLANS, OR AS REQUIRED. BOXES SHALL BE SIZED AS INDICATED ON THE PLANS AND WHERE NOT INDICATED. THEY SHALL BE SIZED N ACCORDANCE WITH THE NATIONAL ELECTRICAL CODE: W. PROVIDE COVERPIATES FOR ALL OUTLET BOXES. X. N ALL CASES, WHERE TWO OR MORE DEVICES ARE INSTALED N GANG BOXES, GANG PLATES WITH SUITABLE OPENINGS SHALL BE PROVIDED. WIRING DEVICES A SUBJECT TO OOMPLWNCE WITH REQUiZEIMENTS. PROVIDE THE FOLLOWING PRODUCTS, OR AN APPROVED EQUAL: 1. TOGGLE SWITCHES: 20 AMPERE, 120 -277 VOLT, AC ONLY, QUIET TYPE, INDUSTRIAL SPECIFICATION GRADE. 2. GENERA. PURPOSE RECEPTACLES NEMA 5 -20R, GROUNDING TYPE, NOU5TRAL SPECIFICATION GRADE. 3, DEDICATED USE RECEPTALLES MEMA 5-202, CROUNDI G TYPE, INDUSTRIAL. SPECIFICATION GRADE. 4. GROUND FAULT CIRCUIT INTERRUPTING RECEPTACLES: ND A 5-208, GROUNDING TYPE, INDUSTRIAL SPECIFICATION GRADE. B. COORDINATE DEVICE FN04 COLORS WHIM ARCHITECT. G PROVIDE OUVERPLATES FOR ALL WRING DEVICES. PROu1DE BLAND OUTLET PLATES FOR ALL TELEPHONE, DATA, AND OTHER RM OUTLET BOXES. PROVIDE METAL SCREWS FOR SECURING PLATES TO DEVICES. D. MULTIPLE OUiLEFS SHALL BE PROVIDED WITH MULTIPLE GANG PULES OF ONE -PIECE CONSTRUCTION. E COVERPUTES FOR ALL SURFACE MOUNTED DEVICES INSTALLED N CAST META. BOXES SHWI. BE GALVANIZED SHEET METAL PATES SPECFICALLY DESIGNED FOR USE WITH CAST METAL BOXES, F. COYERPUTES FOR ALL FLUSH MOUNTED DEVICES SHALL. BE HIGH - IMPACT UNBREAKABLE NYLON. COORDINATE FINISH COLOR WITH ARCHITECT. G. CUOPIAATES FOR ALL SURFACE MOUNTED DEVICES INSTALLED N CAST METAL BOXES SHALT. BE STAINLESS STEEL It C OVERPLATES FOR OUTDOOR OR DUPLEX RECEPTACLES SHALL BE COOPER WPM DEVICES WE ATHERBOX IN-USE TYPE COVER OR APPROVED EQUAL. PANEL80ARDS A PANEL80AROS SHALL BE OF DEAD -FRONT CONSTRUCTION EQUIPPED WITH THERMAL-MOOVIC MOLDED CASE CIRCUIT BREAKERS AS HOifiATED ON THE SCHEDULES AND AS SPECIFIED HERFJN. B. BUS BARS FOR PANE.BOARDS SHALL BE COPPER. C. [4WY/277Vj2081'/120Vj240/12OVj [3111- PHASE, [4131 -WIRE S/N LIGHTING AND APPLIANCE PANELBQAROS SHAT BE SQUARE 0 COMPANY TYPE NOOD, OR APPROVED EQUAL. EQUIPPED WITH BOLT -ON THERMAL - MAGNETIC CIRCUIT BREAKERS. BREAKERS SHALT. BE EQUIPPED WITH INTEGRAL CROSSBAR TO ASSURE SIMLiANEOUS OPENING OR ALL POLES IN MULTIPOLE CiRWIT BREAKERS. BOLT -ON CIRCUIT BREAKERS SHALL BE ABLE TO BE INSTALLED N SAME PANELBOAROS WITHOUT REQUIRING ADDITIONAL HARDWARE. CIRCUIT BREAKERS SHALL. BE RATED (601240Y) WITH CONTINUOUS CURRENT RATNGS, AS NOTED ON THE DRAWINGS. INTERRUPTING RATING SHALL BE AS INDICATED ON MANG;S. AL CIRCUIT BREAKERS SERVING HD LIGHTING LOADS SHALL. BE THE *SW TYPE. ALL CIRCUIT BREAKERS SERVING HVAC EQUIPMENT SHALL BE TOE '1HACR" TYPE FURNISH ALL CIRCUIT BREAKER SERVING EMERGENCY AND /OR LIFE SAFETY EQUIPMENT WITH HANDLE LOCK DEVICES. EACH PANELBOARD SHALL BE EQUIPPED WiTH A BARE UNNSUUTED EQUIPMENT GROUNDING BAR FOR USE N TERMINATING SEPARATE EQUIPMENT GROUNDING CONDUCTORS, D. PROVIDE GAALVANiZED SHEET STEEL CABINET TYPE ENCLOSURES FOR ALL PANELDCAM IN SIZES AND NEI A TYPES, AS HOOTED. RIGIDITY AND GAUGE Of STEEL TO BE AS SPECIFIED N UL STANDARD 50 FOR CABINETS. WIRING GUTTER SPACE TO BE N ACCORDANCE WITH UL STANDARD 67 FOR PANELBOAROS, AS A MINIMUM. ALL PANEL80ARDS SHWA BE SUPPLIED WiTH FRONT PANEL, INMWING A DOOR WiTH FLUSH CYLINDER TUMBLER TYPE LOCK WITH CATCH AND SPRING - LOADED SWLESS STEEL DOOR PULL ALL PANELBOARDS SHWA BE KEYED ALIKE. FRONTS SHALL HAVE ADJUSTABLE INDICATING TRIM CLAMPS WHICH SHALL BE COMPLETELY CONCEALED WHEN DOORS ARE CLOSED. DOORS SHALL BE MOUNTED WITH COMPLETELY CONCEALED STEEL HINGES. FRONTS SHALL NOT BE REMOVABLE WITH DOOR IN LOCKET) POOH A CIRCUIT DIRECTORY FRAME AND CARD WITH CLEAR PLASTIC MUM SHIN. BE PROVIDED ON THE INSIDE OF THE DOOR. EACH PANEi EIGARD SHALL BE FURNSS O WITH HINGED TRIM OPTION. E. MOUNT Al PANELS SO THAT TOP SWITCH OR BREAKER HANDLE IS NO MORE THAN 6' -Y ABOVE THE FINISHED FLOOR LINE. BOTTOM BREAKER OR SWATCH SHALL BE NO LESS THAN 24' ABOVE FINISHED FLOOR. F. TYPE N PANELBOMD'S CIRCUIT DIRECTORY CARD UPON COMPLETION OF INSTALLATION WORK. CIRCAAT AND MOTOR DiSCONECTS A ALL DISCONNECT SWATCHES SHALL BE NE MA TYPE HD AND U LISTED, 240 VOLT OR 600 VOLT RATING AS REQUIRED. 8. SWITCHES SHAH HAVE BLADES WHICH ARE FULLY VISIBLE IN THE 'OFF' POSITION WHEN SWITCH DOOR IS OPEN. LUGS SHALL BE FRONT REMOVABLE AND UL LISTED FOR 7TC COPPER WIRES. C SWITCHES SHALL BE QUICK -MAKE. QUICK - BREAK. SWATCHES SHALL HAVE PROVISIONS FOR PADLOCKING N THE OFT' POSITION WiTH AT LEAST THREE LOCKS, SWITCHES SHALT. HAVE DUI. COVER INTERLOCK TO PREVENT UNAUTHORIZED OPENING OF THE SWATCH DOOR WHEN THE HANDLE iS IN THE "ON' POSITION, AND TO PREVENT CLOSING OF THE SWITCH MECHHANISI WiTH THE DOOR OPE1N. THE HANDLE POSITION SHALL INDICATE WHETHER THE SWITCH IS 'ON' OR W. D. EXCEPT WHERE INDICATED OTERW4SE, SWITCHES FOR USE NDOORS SHALL BE MOUNTED IN NENA TYPE 1 SHEET METAL ENCLOSURES, AND SWITCHES FOR USE OUTDOORS SHALL BE MOUNTED IN N EMA TYPE 3R "TIGHT ENCLOSURES. E ALL FUSIBLE SWITCHES SHALL L BE FURNISHED WITH FUSE CEPS FOR CLASS R FUSES AND SHAD. BE EQUIPPED WiTH PROPER REJECTION CLIPS TO PREVENT THE USE OF LASS H FUSES. F. WHERE SWITCHES ARE USED AS MOTOR BRANCH CIRCUIT DISCONNECTS, AND WHERE A SEPARATE CONTROL CIRCUIT iS USED. THE DISCONNECT SWITCH SHALL HAVE AUXILIARY CONTACTS FOR BREAKING THE CONTROL CRWif WHEN DiSOONNECT SWITCH IS N THE OPEN POSITO4. G>. FURNISH AND INSTALL DISCONNECT SWATCHES WHERE INDICATED ON THE DRAWINGS AD /OR WHERE REQUIRED BY CODE. DISCONNECT SWITCHES %IALL BE FUSIBLE OR NON- FUSIBLE, AS INDICATED, OR REQUIRED, TO PROVIDE THE REQUIRED DISCONNECT MEANS AND /OR BRANCH CIRCUIT PROTECTION. K DISCONNECT SWITCHES SHALL BE AS MANUFACTURED BY SQUARE 0 OR APPROVED EQUAL. SUPPORTING DEViC£S A PROVIDE SUPPORT FOR ALL ELECTRICAL WORK AS INDICATED ON THE DRAWINGS, AS SPECIFIED HEREIN, OR AS REQUIRED BY CODE. B. COMPLY WITH NEC AS APPLICABLE TO CONSTRUCTION AND INSTALLATION OF ELECTRICAL. SUPPORTING DO IICESS. G COMPLY WITH APPLICABLE REQUIREMENTS OF ANSI /NE1MA STO. PUB. NO. F8 1, 'FITTINGS AND SUPPORTS FOR CONDUIT AND GABLE ASSEMBLIES'. D. COMPLY WITH APPLICABLE MSS STANDARD REQUIREMENTS PERTAINING TO FABRICATION AND INSTALLATION PRACTICES FOR PIPE HANGERS AND SUPPORTS. E COMPLY WITH THE NATIONAL ELECTRICAL CONTRACTORS ASSOCIATION 'STANDARD OF NSTAUATiON' PERTAINNG TO ANCHORS, FASTENERS, HANGERS, SUPPORTS AND EQUIPMENT MOUNTING. F. WHERE MANUFACTURED SUPPORTING DEVICES ARE PROVIDED, THEY SHALL COMPLY WITH MANUFACTURER'S STANDARD MATERIALS, DESIGN, AND CONSTRUCTION N ACCORDANCE WITH PUBLISHED PRODUCT INFORMATION. G PROVIDE U- CHANNEL STRUT SYSTEM FOR SUPPORTING SURFACE MOUNTED ELECTRICAL EQUIPMENT, 12 GAUGE MINIMUM SIZE NOT- DIPPED CALVN IM STEEL OF TYPES AND SIZES INDICATED (UNISTRUT P -1000 MINMUM SIZE). K FURNISH AND INSTALL ALL NECESSARY HANGERS, SUPPORTS, ETC., AS REQUIRED. FOR RIGIDLY AND SECURELY MOUNTING ALL SWITCHES, CONNECTOR BOXES. LIGHTING FIXTURES. PANELBQARDS, PULL BOXES, CONDUIT, OUTLET BOXES, AND ALL OTHER ITEMS OF ELECTRICAL WORK INCLUDED N THIS PROJECT. I. ALL HANGARS AND SUPPORTS SHALL BE FASTENED 10 THE BUILDING STRUCTURE BY MEANS OF BOLTS, U- CHWNNEi. STRUT SYSTEiM, MOM AND RODS, OR OTHER APPROVED MEANS, J. TYPE MC CABLES %iA L BE SUPPW O WITHIN 12 INCHES OF EVERY JUNCTION OR OUTLET BOX, AND AT INTERVALS NOT TO EXCEED 6'-0' N AO(XIROM WITH THE NEC. K. LIGHTING FIXTURES SHALL BE SECURELY SUPPORTED FROM THE BUILDING STRUCTURE, AS INDICATED ON THE DRAWINGS OR AS SPECIFIED HEREIN. L DO NOT USE PERFORATED ST "'IRON HANGERS. ON THiS PROJECT FOR ANY PURPOSE. M. SUPPORT BOXES FROM BUILDING STRUCTURE N AN APPROVED MANNEIt MAKE SUPPORT MOD" OF OMIT TO: WHICH THEY ARE CONNECTED. ROD HANGERS SNAIL BE USED WHERE SUITABLE. WHERE ROD HANGERS ARE NOT SUITABLE, PROVIDE U- CHANNEL STRUT SUPPORTS FROM BUILDING STRUCTURE. K WHERE MULTIPLE RUNS OF EXPOSED CONDUIT ARE REQUIRED, PROVIDE UNISTRUT SUPPORTS FOR CONDUIT. 0. WHERE OMIT IS SUPPORTED BY SUSPENDED HANGERS, THE TOTAL LENGTH TO THE BOTTOM OF THE HANGER SHAD. NOT EXCEED 12', OR PROAASiON %A LL BE MADE FOR THE SUPPORT OF REQUIRED SEISMIC LOADING. P. ALL SUPPORT SYSTEMS UTILIZED ON THIS PROJECT SHALI. EMPLOY SCREWS OR BOLTS AND NUTS TO SECURE CABLES, CONDUI, AND CONDUIT SUPPGNRT. SEISMIC RESTRAINTS A INSTALL SEISMIC SUPPORTS FOR ALL NEW ELECTRiCAL SYSTEMS AS REQUIRED BY [1 999 SOC) [2003 W. ASCE 7,1 AND LOCAL. AUTHORITY HAVING JURISDICTION. MIER TO STRUCTURAL. DIRA M FOR SEISMIC CASSIiCATiONS. SECURE THE SERVICES OF AN ENGINEER REGISTERED IN THE STATE OF [ ) TO PROVIDE CALCULATIONS AND SEALED DRAWINGS OF ALL SEISMIC SUPPORT SYSTEMS. B. SEISMIC RESTRAINT MATERIALS SHALL. BE AS MANUFACTURED BY B-LNE SYSTEMS, MASON NDUSTRAS, OR APPROVED EQUAL ELECTTRICA. DENTFIATION A FURPISTR AND INSTALL A CONDUCTOR DENiiFTGATION BAND ON EACH CONDUCTOR IN EACH BOX/ENCLOSURE/CABINET WHERE WIRES OF MCK TAN ONE CIRCUIT ARE PRESENT, EXCEPT WHERE ANOTHER FORM OF IDENTIFICATION. SUCH AS COLOR CODED CONDUCTORS, iS PROVIDED. CONDUCTOR IDENTIFICATION BANDS SHWA BE T & 8 TYPE E -Z, OR APPROVED EQUAL 8, INSTALL A OONTINUOUS UNDERGROUND PLASTIC, CABLE MARKER TAPE A MINIMUM OF 12 INCHES ABOVE ALL UNDERGROUND ELECTRICAL LINES. CABLE MARKER TAPE SHALL BE AS MANUFACTURED BY ALIEN, OR APPROVED EQUAL THE TAPE SWVI BE HEAVY CAKE POLYETN'A.fNE FILM (40 ML THICKNESS), 6' RIDE, BRIGHT YELLOW N COLOR WITH A CONTINUOUS MESSAGE DESIGNATING A BURIED ELECTRIC LINE BELOW. C. ROM AND INSTALL AN DNGi M PLASTIC IAMIATE IDENTIFICATION PUTS AT EACH PANELBOARD AND DISCONNECT SWITCH. SECURE WITH STAINLESS STEEL SCREWS, INCLUDE THE FOLLOWING INNFORMATIOt 1. DISTRIBUTION LIGHTING AND APPLIANCE PANIE1.80ADS - PANEL NAME N 1/4' LETTERS, VOLTAGE AND PHASE N 1/8' LETTERS (E.G., 'PANEL. M. 120/208Y, 3- PHASE. 4 WIRE'). 2. EACH SEPARATE SWITCH CANT AT DISTRIBUTION PANELS - CIRCUIT NUMBER AND LOAD SERVED N 1/8' LETTERS (E.G.. '113. PANEL Al. 3. EACH DUCT SWITCH - LOAD SERVED, VOLTAGE AND PHASE. PANEL AND CIRCUIT NUMBER N 1/8' LETTERS (E.G., 'ACU -1, 208Y. 3- PHASE. M -61. GROUNDING A FURNISH AND INSTALL SYSTEM, DaOSURE. AND EQUIPMENT GROUNDING FOR ALL ELECTRIC WRING FOR THE BUILDING N FULL COMPLIANCE WITH THE REQUIREMENTS OF LOCAL CODES AND THE NEC ALL GROUNDING CONDUCTORS SHALL BE COPPER. B. PROVIDE GROUNDING PRODUCTS THAT ARE UL LISTED AND LABELED AND COMPLY WiTH ESTABLISHED INDUSTRY STANDARDS FOR APPLICATIONS INDICATED . C. GROUND RODS SHALL BE STEEL WITH COPPER WELDED EXTERIOR, 3/4 NCH DIA X 10 FEET. 0. A CONTINUOUS (GREEN) EQUIPMENT GROUNDING CONDUCTOR SHALT. BE PROVIDED WITH ALL FEEDERS AND BRANCH CIRCUITS. THIS GROUNDING CONDUCTOR SHALL BE INSULATED SAME AS REQUIRED FOR 600 VOLT PHASE CONDUCTORS AND SHWA BE GREEN N DOLOR. WHERE POSSIBILL GROUNDING CONDUCTOR SHWA BE SIZED N ACCORDANCE WITH ARTICLE 250 OF THE NEC AND SHALL TERMINATE W MEANS OF COMPRESSION LUGS AT EACH GROUND BUS, PANELBOARO GROUNDING BAR. PULL BOXES, DISCONNECT SWITCHES, STARTERS, MOTORS, AND OTHER DEVICES. E. WHERE SHORT LENGTHS OF FLEXIBLE STEEL CONDUIT ARE USED BETWEEN OUTLET BOXES N HUNG OR ROM CEILING AND FLUSH LIGHTING FIXTURES, THE LIGHTING FIXTURE SHALL BE GROUNDED BY MEANS OF A SEPARATE 112 AWG COPPER (GREEN) COLORED INSULATED GROUNDING WARE RUN WITH THE CIRCUIT CONDUCTORS N THE FLEXIBLE STEEL CONDUIT AND BONDED TO THE OUTLET BOX AND TO THE FACTURE ENCLOSURE BY MEANS OF AN APPROVED SOLDE3RLESS GROUNDING LUG OR CONNECTOR. LIGHTING A PROVIDE ONLY LIGHTING FIXTURES. EXIT SIGNS AND EMERGENCY LIGHTING UNITS WHICH ARE UL LISTED AND LABELED. B. PROVIDE ELECTRONIC FLUORESCENT BALLASTS WHICH ARE HIGH POWER FACTOR (.90 OR ABOVE) AND THERMALLY PROTECTED WiTH AN "A' SOUND RATING BALLASTS SHALT. BE OF EIVO SAYING DESIGN. ELECTRONIC BAIISTS SHALL L HAVE NOT MORE THAN 20 PERCENT HARMONIC DISTORTION, CERTIFIED BY THE MANUFACTRER. C. LAMPS SHALL BE SYLVANA, G.E., PHILIPS, OR APPROVED EQUAL REFER TO LAMP SECTION OF LIGHTING FIXTURE SCHEDULE. D. BATTERY OPERATED FLUORESCENT BMW LIGHTING BALLASTS SHALL BE PERMANEMLY WIRED TO THE BUILDING ELECTRICAL SYSTEM. WHERE INSTALLED N SWITCHED FIXTURES, EMIRGF O BALLASTS AND BATTERIES SHALL BE WIRED UNSWITCHED, AND NORMAL POWER BALLASTS SHAILL BE WPED SWITCHED. C INSTAL PHOTOELECTRIC CONTROLS FOR CONTROL. OF LIGHTNG AS INDICATED ON THE FINNS. F. CLEAN LIGHTING FIXTURES OF DIRT AND DEBRIS UPON COMPLETION OF THE INSTALLATION, PROTECT MAO FIXTURES FROM DAM DURING REMAINDER OF CONSTRUCTION PERIOD. G. AT THE TIME OF SUBSTANTIAL COMPLETION, REPLACE DEFECTIVE OR BURNED OUT LAMPS N ALL LIGHTING FIXTURES. K PROVIDE TO THE OWNER 10 PERCENT SPARE LAMPS OF EACH TYPE INSTALLED. WIRING AND PLUMING EQUIFIHENi A FURNISH AND INSTALL ALL LINE VOLTAGE POWER WPM FOR PLUMBING EQUIPMENT. FURNISH AND INSTALL DISCONNECT SWITCHES AS INDICATED OR REQUIRED. 8. CONNECTIONS TO EQUIPMENT SUBJECT TO MOVEMENT OR VIBRATION SHALL BE MADE WITH LOUD -TIGHT FLEXIBLE CONDUIT. EMPTY CONDUIT SYSTEM FOR TELEPHIONES AND DATA A FURNISH AND INSTALL AN EMPTY CONDUIT SYSTEM FOR TELEPHONE AND DATA OUTLETS AS INDICATED. B. FURNISH AND INSTALL A BLINK COVERRPLATE AT EACH OUTLET. C. 3/4' MINIMUM EMT CONDUIT SHALL BE STUBBED LIP INTO AOESSILE CEILING SPACE FROM EACH TELEPHONE AND /OR DATA OUTLET PROVIDE AN INSULATED BUSHING FOR EACH SNB -UP. WIRING FOR HVAC EQUIPMENT A FURNISH AND INSTALL ALL LINE VOLTAGE POWER. INTERLOCK AND TEMPERATURE CONTROL WANG FOR HEATING, VENTILATING AND AiR CONDITIONING EQUIPMENT. FURNISH AND INSTAL. DISCONNECT SWITCHES AS NOTED OR REQUIRED. B. THE WX CONTRACTOR iS RESPONSIBLE FOR FURNISHING THE ELECTRICAL CONTRACTOR WITH MANUFACTURER'S WIRING DIAGRAMS FOR PROPER OPERATION OF THE WAG EQUIPMENT. C. CONNECTION TO HVAC EQUIPMENT SUBJECT TO MOVEMENT OR VIBRATION SHWA BE MADE WITH LIQUID-TIGHT FLEXIBLE 0004. 0. ALL WIRING INSTALLED OUTDOORS SHALT. BE N CALVANZED RIGID STEEL CONDUIT USING WEATHERPROOF GASKETED CAST METAL. BOXES. FIRE ALARM SYSTEM A FURNISH AND INSTALL ALL CONDUIT, WIRE, AND ACCESSORIES AS REQUIRED FOR AN WELLLI;ENT, NON - OODED, SUPERVISED INTEGRATED FIRE ALARM SYSTEM AS INDICATED ON THE DRAWINGS AND AS SPECIFIED HEREIN. THE ENTIRE SYSTEM SHALL BE DESIGNED AND INSTALLED N ACCORDANCE WITH ALL APPLICABLE LOCAL, STATE, AND NATIONAL CODES. WHEN NO LOCAL. CODES ARE ENFORCED, UTILIZE NFPA 101, 70, 72 AND ADA AS A MINIMUM STANDARD. ALL PART NUMBERS REFERENCED IN THIS SPECIFICATION CONSTITUTE THE TYPE AND QUALITY OF PRODUCT TO USE. ALTERNATE PRODUCTS N NOTIFIER AND SIMPLEX WILL BE CONSIDERED UP 10 10 DAYS PRIM TO 810 DATE F NO ALTERNATE APPROVAL IS OBTAINED, SPECIFIED PRODUCTS SHWA BE PROVIDED. B. FIRE ALARM CONTROL PANEL EST QUICKSiART 1 INTELIM9 SINGLE LOOP LIFE SAFETY CONTROL PANEL OR EQUAL COMPLETE WITH DUAL LIKE DACT AND POWER SUPPLIES AS NECESSARY. , C. FiRE ALARM ANNUNCIATOR PANEL EST QSI -*D-1 WITH QSA -1 -S /F 8EACKBOX OR EQUAL. S=SURFAC&- F =FLUSH D. FiRE ALARM MANUAL PULL STATION: EST SIGH -270 MANUAL. PULL STATION OR EQUAL E FIRE ALARM CEILING SMOKE DETECTOR: EST S&-­PS PHOTOELECTRIC SMOKE DETECTOR WiTH SK,A -S84 MOUNTING OAS OR EQUAL. F. FIRE ALARM CEILING HEAT DETECTOR: EST SIGA --HFS HEAT SENSOR WITH SIGH -S64 MOUNTING BASE OR EQUAL G. FIRE ALARM DUCT SMOKE DETECTOR: EST SICA-SD DUCT SMOKE DETECTOR OR EQUAL. WiTH INTEGRAL CONTROL RELAY; SAMPLING TUBE AND REMOTE TEST STATION H. FIRE ALARM INTERFACE MODULES: ESTSIGA -CT 1/2 MONITOR MODULES, SHGA -CR CONTROL RELAY; SSICA -CCMS NOTIFICATION CIRCUIT MODULES OR EQUAL I. FIRE ALARM AMV09A DEVICES: GTR -HDVM HORN WITH FIELD SELECTABLE MULTI - CANDELA STROBE GTR -W STROBE ONLY, FIELD SELECTABLE MULTi- CANDELA OR EQUAL J. THE FIRE ALARM SHALL BE UL LISTED FOR NFPA 72 A, 8, C, D. AND POWER LIMITED APPLICATIONS PER NEC 760. K. BATTERY SIZING SHALL BE CASED ON A FIVE (5) MINUTE ALARM CONDITION OCCURRING AT THE END OF A 24 HOUR STANDBY MODE. L THIS CONTRACTOR SHWL SUBMIT PLANS TO THE LOCAL RULING AUTHORITY AND OBTAIN APPROVAL PRIOR TO INSTALLATION. AT THE COMPLETION OF THE INSTALLATiON, THIS CONTRACTOR SMALL PROVIDE THE OWNER WITH PLANS APPROVED BY THE LOCH. RULING AUTHORITY AND A LETTER OF ACCEPTANCE FROM THE RULING AUTHORITY. M. PROVIDE AND NSTAU. WHERE SHOWN, A FIRE ALARM CONTROL, PANEL, COMPLETE WAIN ALL MODULES, POWER SUPPLIES, STANDBY BATTERIES, AND SOFTWARE FOR A COMPLETE AND WORKING SYSTEM AS SHOWN ON THE PLANS AND SPECIFIED EERFIN. N. PROVIDE NON - VOLATILE PROGRAMMABLE MEMORY WITHIN THE CONTROL PANEL. LOSS OF PPoMWRY AND SECONDARY POWER SHALL NOT ERASE THE INSTRUCTIONS STORED IN MEMORY. 0. PROVIDE TRANSFORMERS. FUSES. AUXILIARY RELAYS FOR CENTRAL STATION, AILU SHUTDOWN AND FUNCTIONS DESCRIBED TO PROVIDE A WORKING SYSTEM AS SPECIFIED. P. PROVIDE AN ADDRESSABLE INTERFACE MODUS FOR COMIMUNHCAIING WITH UP TO 150 ADDRESSABLE DEEAC'ES. Q. THE FIRE HARM SYSTEM SHALL BE INSTALLED IN A CONTINUOUS CONDUIT SYSTEM IN ACCORDANCE WiTH THE BASIC M90M AND METHODS SECTIONS OF THIS DIVISION OF THE SPECIFICATIONS. R. INSTALL ALL WRING N ACCORDANCE WiTH FiRE ALARM SYSTEM MANUFACTURER'S WRITTEN INSTRUCTIONS AND RECOMMENDATIONS, INCLUDING SIZE AND TYPE OF WIRE USED. S. ALL WIRING SHALL MEET NATIONAL. ELECTRICAL CODE ARTICLE 760 FOR FIRE ALARM WPM ALL WARE SMALL BE TAGGED AT ALL JUNCTION POINTS AND SHALL TEST FREE OF GROUNDS, T. PROVIDE TIRES (3) COPIES OF MAINTENANCE MANUALS FOR THE OWNER'S USE U. FIRE HARM SYSTEM INSTALLATION INSPECTION AND FNA ADJUSTMENT SAIL BE PERFORMED BY SPECIALLY TRAINED PERSONNEL ODOM A REMOVE ALL FIXTURES AND DEVICES SHOWN TO BE DEMOLISHED ON THE DRAWINGS. 8. EQUIPMENT NOT BEING MUSED N THE PROJECT IS TO BE REMOVED FROM THE SITE. ONCE REUM iT BECOMES THE CONTRACTOR'S PROPERTY AND RESPONSIBILITY. C. WHERE POSSIBL& REUSE EXISTNG CONDUIT AND WIRE IN PUCE. REMOVE FROM THE SITE CONDUIT AND WiRE NOT BEING REUSED. ONLY REUSE CONDUIT AND WIRE THAT CAN REMAIN IN PLACE. DO NOT REINSTALL OLD CONDUIT OR WIRE ONCE R HAS BERME DEMOLISHED. 0. WHERE EXISTING DEVICES AND/OR FIXTURES ARE TO REMAIN. CLEAN AND INSPECT THE EQUIPMENT TO VERIFY THAT IT IS FIT FOR CONTINUED SERVICE. I- AT THE COMPLETION OF EACH DAYS WORK, REMOVE FROM THE SITE ALL RUBBISH AND DEMOLISHED CONDUIT, WIRE. FIXTURES, DEVICES, ETC. THAT ARE NOT TO BE REUSED N THE PROJECT. IT SHALL. L BE THE ELECTRICAL. CONTRACTOR'S RESPONSiMN TO CLEAN DIM CAUSED BY HIS OR HER PORTION OF THE WORK If, Architecture 1500 Union V �j Planning Avenue 06 ' - -'x F Interior 11 Memphis, TN �,t. Design 38104 - :! e, _ - . J Tel. 901 - 27&8868 www.anfa.com r' 4',, \.YIN.. O Y' P. .F. ) 1 ,, .dJA' i 91, mo� 0 it o REV. NO. I DATE I DESCRIPTION PROJECT STATUS CONSTRUCTION DOCUMENT PROJECT NAME ONE 7000 PLACE SW 62 AVE. MIAMI, FL 33143 SHEET TITLE ELECTRICAL SPECIFICATIONS 7' ..e � '- .. * _ _�. SEAL , - t ;_ If dr �,>, ,� y' -11 �� r .A •'4"; N %< ,(: b� a. > - r I. 4 L . �� v DRAM CHECKED PROJECT NUMBER�- r GDW DEC 08048 � DATE SHEET NO. y \ 07 -08 -2009 E 2 0 0 © 2009 ASKEW NIXON FERGUSON ARCHITECTS I i �_ 1111`