13-452-064Energy Shield Thermal Barrier Pai #t Additive Application Specification Sheet
SURFACE PREPARATION
GENERAL: The entire surface
area to be painted should be
clean, dry, sound, and free from
all dirt, grease, oils, waxes,
mildew and any other surface
contaminants. Surface areas
affected by mildew growth
should be properly scrubbed
with a soft - medium bristle
scrub brush and a solution of
240m1 Tri- Sodium Phosphate
(TSP) mixed with one (1) liter
household bleach and three (3)
liters of warm water, per 4 liter
solution. Allow solution to
stand on the affected surface
areas for approximately 10 -20
minutes, then rinse thoroughly
with clean water and allow 24-
48 hours to dry properly.
Remove any loose scale,
chalked, cracked or peeling
paint from previously painted
substrates by hand scraping,
sanding, wire brushing, and or
power tool cleaning. Previously
painted substrates that show
signs of severe delaminated
surfaces should be completely
stripped down to a more
suitable and or stable substrate.
Repair / replace any damaged
and or delaminated su rface
areas. Lightly sand smooth all
rough paint edges to the
adjacent surface area and sand
all glossy surfaces to effectively
dull any existing sheen levels.
PRODUCT APPLICATION:
Apply when surface and
ambient temperatures are
above 55/F. and below 90 /F.
KEEP PRODUCT FROM
FREEZING!
Applywith a quality brush,
roller, or airless spray
equipment
For bestresults, applywith a
brush and /or roller effectively
working into surface pores. If
applying with a brush, apply a
smooth and generous coat
application on smaller surface
areas, such as trim or cutting -in
larger surface areas. If applying
with a roller cover, apply an
even and generous coat
application in an "M" or
crisscross motion, avoiding any
excessive re- spreading or
reworking. Always maintain a
proper wet edge by
brushing /rolling into
previously applied coating area.
If using a spray application
method, the surface areas
should be properly hack - rolled
to effectively work into surface
pores, ensure proper adhesion
and an even coat application.
All application methods are
approximate. Application
procedures may be contingent
upon specifications ofthe paint
used in conjunction with this
product.
METHOD Brush: Synthetic
Roller: 9.5Zmm- 12.7mm Nap
Airless Spray: Minimum 2000
psi
Tip: 0.43mm- 0.48mm
-CLEANUP
Spills, splatters, tools, and
equipment easily cleanup with
warm soapy wa ter, B e sure to
flush all to ols a nod equ ipment
used in the application process
with warm soapywater.
IMPORTANT
ALLTECHNICAL DATA
INFORMATION CDNTAINED
HEREIN IS ACCURATE TO THE
BEST OF OUR KNOWLEDGE. ALL
WARRANTI ES AR E EXC LUD ED,
WHETHER EXPRESSED OR
IMPLIED BY OPERATION OF LAW
OR OTHERWISE, INCLUDINGALL
I MP LIE D WARRANTI ES OF
MERCHANTA 13II,1ITOR FITNESS
FORA PARTICULAR PURPOSE,
SELLER SH ALL N0 T B E LIAB LE,
(D [ RECTLY OR I N DIRECT LY),
UN DER ANP CIRCUMSTANCES FOR
CONSEQUEN T AL., I NCID ENTAL,
SPECIAL OR.A►N5' OTHERTYPE OF
DAMAGES ARISING OR RESULTING
FOR ANY REASON UNDER THE
SALE, HANDL I NG, OR US E 0 F
GOODS SO LD, 5 EL LE R'S LLABILITW
HEREUND ER, AN D RUYER'S
EXCLUSIVE REMEDY HEREUNDER,
FO R NE GL 1GE N CE OR ANY 0TH E R
REASO N. IS EX PRESSLY LIM ITE D
TO RE[ MBURSEMEN T 0 F THE
PURCHASE P RICE OF THE
MATERIALS SOLD AFTER PROOF
OF PURCHAS E IS PROVIDED TO
THE SELLER N07 CE OF ANY
ALLEGED FAIL.UREOR DEFECT [N
THE MATERIALS OUST BE GIVEN
TO THE SELLER IN riWRITING BY
CERTIFIED US. MAIL WITHIN 15
DAYS OF F 114ST N 071C ING THE
PROBLEM. FAILURETO GIVE THE
REQUIRED NOTICE WET HIN THE
TIME P ROVI DED CO N STITUTES A
WAIVER 0F ANY CLAIM. THE
MANUFACTURERI5 NOT
RESPONSIB LE FOR ANY
MISREPRESENTATION MADE BY
THE DEALER-
NOTE THAT IN FORMATION
WITHIN THIS DOCUMENT IS
SUBJECT TO CB.ANIGE
WITHOUT NOTICE_ PLEASE
CONSULT YOUR DEALER OR
REPRESENTATIVE FOR THE
MOST RECENT REVISIONS OF
TPIC r�rRnR -i A'AT1nM