13-62 (2)-009System No. C -AJ -1226
F Rating — 3 Hr
T Rating — 0 Hr
L Rating At Ambient — Less Than 1 CFM /Sq Ft
L Rating At 400 F — 4 CFM /Sq Ft
A
SECTION A-A
1 1. Floor or Wall Assembly — Min 4-1/2 in. thick reinforced lightweight or normal weight (100-150 pco concrete.
Wall may also be constructed of any UL Classified Concrete Blocks*. Max diarn of opening is 32 in.
2. Metallic Sleeve — (Optional) Norn 32 in. diarn (or smaller) Schedule 40 (or heavier) steel sleeve cast or grouted
into floor or wall assembly, flush with floor or wall surfaces or extending a max of 3 in. above floor or beyond
both surfaces of
square 3. Sheet Metal Sleeve — (Optional) Max 6 in. diam, min 26 ga gaiv steel provided with a 26 ga gaiv steel square
flanqe spot welded to the sleeve at approx mid-height, or flush with bottom of sleeve in floors, and sized to be a
min of 2 in. larger than the sleeve diam, The sleeve is to be cast in place and may extend a max of 4 in. below
the bottom of the deck and a max of 1 in. above the top surface of the concrete floor.
4. Sheet Metal Sleeve — (Optional) - Max 12 in. diam, min 24 ga gaiv steel provided with a 24 ga galv steel
g e spot welded to the sleeve at .r• • mid-height, or flush with bottom of oo and sized
to be a min of 2 in, larger than the sleeve diam. The sleeve is to be cast in place and may extend a max of 4 in.
below the bottom of the deck and a max of I in, above the top surface of the concrete floor.
5. Through-Penetrant — One metallic pipe, tube or conduit to be installed either concentrically or eccentrically
within the firestop system. The annular space between penetrant and periphery of opening shall be min 1
(point contact) to max 1-7/8 in. Penetrant may be installed with continuous point contact. Penetrant to be rigidly
pport • on both sides of • • or - # The following • - s sizes of penetrants • -
used:
A. Steel Pipe — Norn 30 in. . . -. ti . pipe.
B. Iron Pipe — Nom 30 in. diarn (or smaller) cast or ductile iron pipe.
C. Copper Pipe — Norn 6 in. diarn (or smaller) Regular (or heavier) copper pipe.
D. Copper Tubing — Nom 6 in. diarn (or smaller) Type L (or heavier) copper tubing.
E. • iuit — Nom • in. f (or smaller) steel conduit.
Conduit — • 4 in. ! # tubing
6. Firestop System — The firestop system shall consist of the following:
A. Packing Material — Min 4 in. thickness of min 4 pcf mineral wool batt insulation firmly packed into opening as a
permanent form. Packing material to be recessed from top surface of floor or sleeve or from both surfaces of
wall or sleeve as required to accommodate the required thickness of
concrete B. Fill, Void or Cavity Material* — Sealant — Min 1/4 in. thickness of fill material applied within the annulus, flush
with top surface of floor or sleeve or with both surfaces of wall or sleeve. At the point or continuous contact
locations between penetrant and concrete or sleeve, a min 1/4 in. diam bead of fill material shall be applied at
the or pipe pe on #s surface of rr and on both surfaces of
CONSTRUCTION HILTI DIV O FS-One Sealant
*Bearing Classification Mark
1
Reproduced by HILTI, Inc. Courtesy of
Underwriters Laboratories, Inc.
nRESTOP SYSMEMS June 27, 2007
r
DR FDS
IDULET (THREADLESS FOR
D THICK WALL
IDUIT
+II
N.T.S.
NOTE: TO BE USED IN SERVING LINE AREA.
System No. W -L -1054
F Ratings -1 and 2 Hr (See Items 1 and 3)
T Rating - 0 Hr
L Rating At Ambient - Less Than 1 CFIl Ft
L Rating At 400 F - 4 CFM /Sq Ft
SECTION A-A
1. Wall Assembly – The 1 or 2 hr fire -rated gypsum wallboard /stud wall assembly shall be constructed of the materials and in
the manner specified in the individual U300 or 0400 Series Wall and Partition Designs in the UL Fire Resistance Directory
Z Through- Penetrants – One metallic pipe, conduit or tubing to be installed either concentrically or eccentrically within the
firestop system. The annular space shall be min 0 in. to max 2 -1/4 in. Pipe may be installed with continuous point contact.
Pipe, conduit or tubing may be installed at an angle not greater than 45 degrees from perpendicular. Pipe, conduit or tubing
to be rigidly supported on both sides of wall assembly. The following types and sizes of metallic pipes, conduits or tubing
may be used:
A. Steel Pipe – Nom 30 in diam (or smaller) Schedule 10 (or heavier) steel pipe.
B. Iron Pipe – Nam 30 in. diam (or smaller) cast or ductile iron pipe.
C. Conduit – Nom 4 in diam (or smaller) steel electrical metallic tubing or 6 in. diam steel conduit.
D. Copper Tubing – Nom 6 in. diam (or smaller) Type L (or heavier) copper tubing.
E. Copper Pipe – Nom 6 in. diam (or smaller) regular (or heavier) copper pipe.
F. Fill, Void or Cavity Material* – Sealant -- Min 5/8 in. thickness of fill material applied within the annulus, flush with both
surfaces of wall. At the point or continuous contact locations between pipe and wall, a min 1/2 in. diam bead of fill material
shall be applied at the pipe wall interface on both surfaces of wall.
HILTI CONSTRUCTION CHEMICALS, DIV OF
HILTI INC – FS -One Sealant
*Bearing the UL Classification Mark
CONCRETE SLAB PIPE PLUG SLOTTED BRASS
IFINISH FLOOR
EXPANSION JOINT MATERIAL
CONDUIT EXPANSION FITTING
FO-Z CO. TYPE °AX-
BONDING JUMPER
O -Z CO. TYPE 'AJ"
EXPANSION FITTING DETAIL.
1. PROVIDE ELECTRONIC BALLAST AND IN-LINE FUSES FOR ALL FLOURESCENT FIXTURES.
i • iF '
• Relay
• Powerpock
• Wall Switch
Normal Line j ' Normal Lighting
_ r—a
Normal Neutral
"Sensing"
Line
Emergency Line
Emergency Neutral
"Switching"
Line
Normal
LIGHTING
FIXTURE
S C H E D
U L E
Normal. Neutral
(WHITE
18AWG)
Normal Power
Sense
LAMPS
FIXTURE
TYPE
MANUFACTURER & CATALOG No.
MOUNTING
(OR APPROVED EQUIVALENT)
NO.
TYPE
WATTS
SERVICE
TOTAL
VOLTS
WATTS
BDL
A
PENDANT
2
CF26 35K
26
UNV
54
DB L -AC-W H -2C -277 -1.8K
LIGHTING ARTISTRY
B
PENDANT
1
676.35 T4
35
120
35
ET-MINX
LIGHTING ARTISTRY
C
PENDANT
1
CF32 835
32
120
32
TL- 422- 700- TD-DLN P W- NS -CF277
DELTA
D
SURFACE
4
WW LED
4.2
120
16.8
6 275 07 24 277
INFINITY
E
RECESSED
2
CF26 35K
26
UNIV
54
P H60 -226 Q E B 2 -CS -U NV -M W T
FINELITE
F024T5H0
F
GRID
2
24
120
48
H P R -A- 2X2- DC- 2T5HO- 277V -S C-C1 -I S
835
HE WILLIAMS
G
50GS24- 332SA12125- G3- EB3 -UNV-
GRID
3
F032T8 835
28
UNIV
84
F338 -LP835
LEUCOS USA
GU-5.3
H
RECESSED
1
N
50
INC
50
SD-88
BEGHELLI
X
UNIVERSAL
LED
4
UNIV
INC
VA4RSA
BEGHELLI
XE
RECESSED
LED
4
UNIV
INC
OL2- SA- LR- 1 /2 -MCR
1. PROVIDE ELECTRONIC BALLAST AND IN-LINE FUSES FOR ALL FLOURESCENT FIXTURES.
i • iF '
• Relay
• Powerpock
• Wall Switch
Normal Line j ' Normal Lighting
_ r—a
Normal Neutral
"Sensing"
Line
Emergency Line
Emergency Neutral
wolf #
METAL GALVANIZED HOUSING
/ CIR.#
t } Q _r
r® ¢w claw
PUSH '3;::
TO TEST 0r } ®� 0 a°
W
U
Z
W
Emergency Lighting Control
11 Typical Wiring
MW i ...ate
)ITI H_MI/ EMI HOSPITAL
w . Sup !!SET CAFE
CAFETERI RENOVATION
_ 6�OQ S`wW- '73rd STREET
MIAMI, FL 33143
3390 Mary Street, Suite 216
Miami Florida 33133 USA
T: 305.461.9480 F: 305.461.3686
Associate Architect
061 -10064 -020
Architects Project Number
FUEL F'FFZMI I
11 /1 qoni 9
DATE
04.24.13
LIGHTING FIXTURE �
SCHEDULE • r DETAILS
ELECTRICAL
Atoll
"Switching"
Line
Normal
Switched
Sense
(RED
18AWG)
Normal. Neutral
(WHITE
18AWG)
Normal Power
Sense
wolf #
METAL GALVANIZED HOUSING
/ CIR.#
t } Q _r
r® ¢w claw
PUSH '3;::
TO TEST 0r } ®� 0 a°
W
U
Z
W
Emergency Lighting Control
11 Typical Wiring
MW i ...ate
)ITI H_MI/ EMI HOSPITAL
w . Sup !!SET CAFE
CAFETERI RENOVATION
_ 6�OQ S`wW- '73rd STREET
MIAMI, FL 33143
3390 Mary Street, Suite 216
Miami Florida 33133 USA
T: 305.461.9480 F: 305.461.3686
Associate Architect
061 -10064 -020
Architects Project Number
FUEL F'FFZMI I
11 /1 qoni 9
DATE
04.24.13
LIGHTING FIXTURE �
SCHEDULE • r DETAILS
ELECTRICAL
Atoll