14-403-024I
L
MECHANICAL GENERAL NOTES
1. THE SPACE IS EXISTING AND HAS PREVIOUSLY BEEN OCCUPIED. REMOVE
EXISTING DUCTWORK, PIPE, ETC., NOT REQUIRED FOR THE NEW INSTALLATION.
2. FURNISH AND INSTALL NEW DIFFUSERS AND REGISTERS AS SHOWN AND
SPECIFIED. FURNISH AND INSTALL VOLUME DAMPERS AT ALL NEW BRANCH
TAKEOFFS,
3. TEMPERATURE CONTROLS, INCLUDING WIRING, SHALL BE PART OF THE
MECHANICAL CONTRACT.
4. FIBERGLASS DUCTWORK IS NOT PERMITTED.
5. FLEXIBLE DUCTWORK MAY BE USED FOR VERTICAL DIFFUSER CONNECTIONS
ONLY AND SHALL BE LIMITED IN LENGTH TO 5' -Or MAX.
6. ALL DUCTWORK SHALL CONFORM TO THE LATEST EDITION OF SMACNA
STANDARDS AND RECOMMENDATIONS.
7. DUCT SIZES SHOWN ARE INSIDE CLEAR DIMENSION AND SHALL BE
ADJUSTED IF REQUIRED TO ACCOUNT FOR METHOD OF INSULATION.
S. FIRE STOP ALL PENETRATIONS THROUGH FIRE RATED PARTITIONS (IF
REQUIRED) IN STRICT ACCORDANCE WITH ALL APPLICABLE STATE AND LOCAL
CODES. VERIFY EXACT METHOD OF FIRE AND MOISTURE CONTROL WITH
LANDLORD AND /OR ARCHITECT.
TEMPERATURE CONTROL NOTES
1. TEMPERATURE CONTROLS SHALL BE A PART OF THE MECHANICAL WORK.
FURNISH AND INSTALL ALL COMPONENTS, INCLUDING THERMOSTATS, TIME
CLOCK, PNEUMATIC TUBING, ELECTRIC WIRING, PE SWITCHES, ETC., REQUIRED
FOR A COMPLETE SYSTEM.
2. EXISTING OUTSIDE AIR DAMPER AND DUCTWORK TO REMAIN.
3. ON DAY CYCLE:
A. SUPPLY FAN RUNS CONTINUOUSLY.
B. FRESH AIR DAMPER OPEN.
C. ON A CALL FOR COOLING FROM ANY THERMOSTAT, THE CHILLED WATER
CONTROL VALVE SHALL MODULATE TO THE FULL OPEN POSITION AS REQUIRED
TO SATISFY THE THERMOSTAT.
4. ON NIGHT CYCLE:
A. SUPPLY FAN OFF.
B. FRESH AIR DAMPER CLOSED.
C. COOLING COIL VALVE CLOSED.
5• CONTROLS SHALL BE INSTALLED COMPLETE AS A SUBCONTRACT TO THE
MECHANICAL CONTRACT BY A CONTRACTOR SPECIALIZING IN TEMPERATURE
CONTROLS. INSTALLATION BY ANYONE OTHER THAN A CONTROL
SUBCONTRACTOR WILL NOT BE PERMITTED.
FIRE PROTECTION NOTES
1. FIRE PROTECTION WORK SHALL BE A PART OF THE MECHANICAL CONTRACT.
THE SPRINKLER SYSTEM SHALL BE INSTALLED AS REQUIRED TO ACCOMMODATE
NEW PARTITIONING AND NEW CEILINGS. SPRINKLER HEAD LOCATIONS SHALL
BE REVIEWED AND APPROVED BY A CERTIFIED SPRINKLER SUBCONTRACTOR
PRIOR TO INSTALLATION, ETC.
SPRINKLER SUBCONTRACTOR SHALL RELOCATE THE EXISTING HEADS AND /OR
FURNISH AND INSTALL NEW AS REQUIRED. ADJUST INSTALLATION AS
DESCRIBED BELOW FOR PROPER COVERAGE, MINIMUM INSTALLATION
REQUIREMENTS, ETC.
2. ALL SPRINKLER HEADS IN AREAS WITH FINISHED CEILINGS ("PUBLIC" AREAS
- SALES AREA, FITTING ROOMS, ETC.) SHALL BE SEMI - RECESSED PENDANT
TYPE WITH WHITE FINISH. SPRINKLER HEADS IN "WORK" AREAS (STOCK ROOM,
TOILET ROOM, ETC.) SHALL BE ROUGH BRASS PENDANT TYPE WITH HEAD
GUARDS.
3. COVERAGE FOR THE SPRINKLER HEADS SHOWN SHALL BE NO GREATER
THAN 130 SF AND SHALL BE VERIFIED BY A CERTIFIED SPRINKLER
SUBCONTRACTOR.
4. CERTIFIED SPRINKLER SUBCONTRACTOR SHALL INCLUDE LAYOUT DRAWINGS
AND ALL REQUIRED LANDLORD AND AGENCY APPROVALS AS PART OF HIS
WORK. SPRINKLER SUBCONTRAC72RSUBMITTAL SHALL INCLUDE, BUT NOT
BE LIMITED TO, THE FOLLOWING AS REQUIRED TO OBTAIN ALL APPROVALS:
A. SPECIFICATIONS FOR ALL PIPING, PIPE FITTINGS, GATE VALVES, DRAIN
VALVES, CHECK VALVES, PIPING SUPPORTS, VALVE HOSE CONNECTIONS, ALL
IDENTIFICATION AND SIGNAGE AS REQUIRED TO ACCOMPLISH ALL TESTS, ETC,
B. APPROVED HYDRAULIC CALCULATIONS PRIOR TO COMMENCING WORK.
C. DENSITY AS REQUIRED FOR THE INSTALLATION AND IN ACCORDANCE WITH
ACCEPTED DESIGN STANDARDS.
D. ISO APPROVAL PRIOR TO COMMENCING WORK.
E. TESTING AND TEST CONNECTIONS.
F. COMPLIANCE WITH ALL DRAWINGS AND SPECIFICATIONS.
G. PERMITS AND BUILDING DEPARTMENT FILINGS.
H. WRENCHES: FURNISH TWO (2) SPANNER WRENCHES FOR EACH TYPE AND
SIZE OF VALVE CONNECTION AND FIRE HOSE COUPLING.
5. LAYOUT OF SPRINKLERS SHALL BE IN CAREFUL COORDINATION OF THE
DRAWINGS, DETERMINING PROPER ELEVATIONS, LOCATIONS, ETC. COORIDINATE
WITH OTHER WORK, INCLUDING INTERFACE WITH LANDLOIRDMAINS, ETC.
6. SPRINKLER SUBCONTRACTOR SHALL COMPLY WITH THE LATEST NFPA, STATE
UNIFORM FIRE PREVENTION AND BUILDING CODES AS REQUIRED.
7. SPRINKLER SUBCONTRACTOR SHALL HAVE A MINIMUM OF FIVE (5) YEARS
EXPERIENCE IN THE INSTALLATION OF FIRE SPRINKLER SYSTEMS.
S. DELIVER THREE (3) SETS OF APPROVED SPRINKLER DRAWINGS TO TENANT.
9. COORDINATE WITH SPRINKLER COMPANY FOR SUBMISSION OF A TEST
REPORT TO THE LOCAL FIRE AGENCY STATING THAT SYSTEM IS IN GOOD
WORKING ORDER AND IS OPERATIONAL.
SYMBOLS AND ABBREVIATIONS
CFM
CUBIC FEET PER MINUTE
o KEY
NOTES
I.
EXISTING AIR HANDLING UNIT SUSPENDED ABOVE
CEILING TO REMAIN, UNIT SHALL REMAIN BALANCED TO 4000
SUPPLY AIR
CFM.
RETURN AIR
O.A.
2.
EXISTING TOILET EXHAUST
FAN TO REMAIN.
CONSISTING OF, BUT NOT LIMITED TO, THE FOLLOWING:
3.
EXISTING DUCT MOUNTED
SMOKE DETECTOR TO REMAIN.
4.
FURNISH AND INSTALL NEW A.C. UNIT CONTROLS.
LIGHTSTAT, MODEL #TME -P01 AND REMOTE SENSOR MODEL
#TME -RRS.
C. CHECK CHILLED WATER PIPING SYSTEM FOR LEAKS. REPAIR AS REQUIRED.
'A' -ISSUE LL. RID, PERMIT
D. CHECK CHILLED WATER CONTROL VALVE. REPLACE OPERATER IF REQUIRED.
DATE 3/u/14
SYMBOLS AND ABBREVIATIONS
CFM
CUBIC FEET PER MINUTE
CD
CEILING DIFFUSER
RAR
RETURN AIR REGISTER
S.A.
SUPPLY AIR
R.A.
RETURN AIR
O.A.
OUTDOOR AIR
t�T
THERMOSTAT
CONSISTING OF, BUT NOT LIMITED TO, THE FOLLOWING:
SMOKE DETECTOR
OR
REMOTE SENSOR
Q EXR i EXR. EX# EX + I EX w EX
EX
EX
t
/ I
_ _
EXR EXR EXR
EX
EX EX EX EX I
/ t II t 400 CFM 300 CFM 800 CFM II I1I
a
EX I I 400 CFM
I I EX I � �' � � ;i,:� °UNE`,`Es<''T'UAC
I I
�- -Nrp 'te S x I; P:a rE� rl� -
EX I t�GRKINGPIA'''.AS E:'�iFPAI3
ww I 6WST BE StTBN' ITTF D T'O AND APPROVED '
/ Ex �.._._r..._... - - - - -- --- ..._�. -.._ ._._.- I I Ex} EX �� I i � T THIN!IA� I
i , JE FIRE DEPARTMENT
i + I I I I / I ? F,FnRF ANY rIkE I ROTECTION SYSTEM
I
+ E T5 INSTAILLEV OR REMODEir-t 411
_ I I EX I I i I} �I
T 3 p(E) D In
/ 25 CFM I I
EX EXR I .800 CFM
EXR I I EX I I L
/ I I i I I EXR \
EX O II II \\
I 300 CFM I I EXR \ \
125 CFM 2� CFM I I EX EX E} I I \
I I I I I _w Ex♦ / EX \ I I I I EX I \ \
�\ t I I ExI I III \\
- 800 CFM II 3 \ \
Ex °` - - - - - -- EX EX
I_ --
_----- - - - - -5 --- - - - --- - --- - - - -�I
Ex I
2 E3 ----- CIV J
25 CFM - - NEW.4 t f
EX
EXR
I
�E
LIGHTS HAVE BEEN TURNED OFF FOR
CLARITY - SEE SHEET E1.0 OR
ARCHECTURAL RCP FOR LOCATIONS.
rt &V%Ar% r%1 A 1k I Irnt t o I\III/'% A l IA /r%Mlr
SCALE 1/4• - 1-0•
•••
••G ••• •
MECHANICAL WORK NOTES - GENERAL,
1. MECHANICAL WORK SHALL BE COMPLETE IN EVERY DETAIL AND ALL
MISCELLANEOUS ITEMS OF MATERIAL AND LABOR NECESSARY TO COMPLETE THE
WORK DESCRIBED, SHOWN OR REASONABLY IMPLIED ON DRAWINGS OR **'.
SPECIFICATIONS SHALL BE INCLUDED IN THE CONTRACT. CONTRACTOR SHALL BAKE, I
MINOR ADJUSTMENTS TO THE WORK WHERE REQUESTED BY THE TENANT, WHEN,, w
SUCH ADJUSTMENTS ARE NECESSARY TO PROPER OPERATION AND WITHIN THE INTENT
OF THE CONTRACT.
2. MECHANICAL CONTRACTOR SHALL VISIT THE SITE AND VIEW ALL EXISTING
CONDITIONS BEFORE SUBMITTING A PROPOSAL FOR THE WORK AS DESCRIBED AAD
SHOWN. NO EXTRAS WILL BE ENTERTAINED FOR FAILURE TO MAKE THIS VISIT.
3. MECHANICAL CONTRACTOR SHALL ACCEPT SOLE AND COMPLETE RESPONSIBILITY
FOR CONDITIONS OF THE JOB SITE, INCLUDING SAFETY OF ALL PERSONS AND
PROPERTY DURING PERFORMANCE OF THE WORK.
4. CONFORM TO GENERAL CONTRACTOR'S SCHEDULE AND INSTRUCTIONS
THROUGHOUT THE DURATION OF THE PROJECT AS REQUIRED TO COMPLY IN EVERY
WAY NECESSARY.
5. CONTRACTOR SHALL NOTIFY THE ARCHITECT AND /OR ENGINEER OF ERRORS,
OMMISSIONS OR DISCREPENCIES BEFORE CONSTRUCTION OR FABRICATION OF
AFFECTED WORK, OR, FAILING SUCH NOTICE, SHALL BE RESPONSIBLE FOR
CORRECTING SAME WITHOUT COST TO TENANT, ARCHITECT OR ENGINEER.
6. ORDER EQUIPMENT ON A TIMELY BASIS (WITHIN 5 DAYS OF RECEIPT OF
CONTRACT) TO MAINTAIN CONSTRUCTION SCHEDULE.
7. SUBMIT FIVE (5) COPIES OF SHOP DRAWINGS OF ALL EQUIPMENT FOR REVIEW BY
THE ENGINEER /ARCHITECT. ONE (1) COPIES WILL BE RETAINED FOR RECORD.
ONLY FURNISH SYSTEMS, EQUIPMENT AND MATERIAL IN COMPLIANCE WITH APPROVED
SHOP DRAWINGS.
S. WORK SHALL INCLUDE STARTUP OF ALL SYSTEMS, FURNISHING OF OPERATING
AND MAINTENANCE INSTRUCTIONS, WARRANTEE FOR ALL EQUIPMENT AND ONE YEAR
GUARANTEE OF ALL WORKMANSHIP, COMMENCING ON DATE OF ACCEPTANCE BY THE
TENANT.
9. WORK SHALL ALSO INCLUDE FULL ONE (1) YEAR MAINTENANCE, PARTS AND
SERVICE CONTRACT FOR ALL EQUIPMENT FURNISHED UNDER THE CONTRACT.
10. ON ALL AIR CONDITIONING EQUIPMENT WHICH INCLUDES COMPRESSORS
(ROOFTOP, SPLIT SYSTEMS, ETC.), INCLUDE AN EXTENDED FOUR (4) YEAR WARRANTY
FOR THE COMPRESSOR.
11. VOLUME DAMPERS, SPUTTERS AND DEFLECTORS SHALL BE INSTALLED IN ALL
DUCTS TO PERMIT ACCURATE BALANCING OF SYSTEM. THE DAMPERS, SPUTTERS
AND DEFLECTORS SHALL BE ADJUSTED TO SATISFY THE HVAC REQUIREMENTS OF THE
CONDITIONED SPACE AND LOCKED IN PLACE AS REQUIRED.
12. WORK SHALL ALSO INCLUDE TESTING AND BALANCING OF A.C. SYSTEM BY A
CERTIFIED BALANCING CONTRACTOR. CONTRACTOR SHALL SUBMIT COPIES OF TEST
AND BALANCE REPORTS SHOWING DETAILED RESULTS OF WORK, INCLUDING, BUT NOT
LIMITED TO THE FOLLOWING: FLOW READINGS, STATIC PRESSURES, TEMPERATURE
READINGS, MOTOR AMPERAGE, BALANCING OF AIR QUANTITIES TO PLAN
REQUIREMENTS, ETC. AS REQUIRED. MAKE ALL ADJUSTMENTS AS REQUIRED TO
PROVIDE DESIGN AIR FLOW.
13. FURNISH ALL EQUIPMENT MANUALS AND WARRANTIES TO TENANT AT THE
COMPLETION
OF THE PROJECT.
14. WHERE APPLICABLE, FURNISH AND INSTALL VIBRATION ISOLATION AS REQUIRED
TO REDUCE, LIMIT OR REMOVE ALL VIBRATIONS FOR ALL MOVING EQUIPMENT.
VIBRATION ISOLATION SHALL BE IN ACCORDANCE WITH ASHRAE RECOMMENDATIONS.
15. PROVIDE ENGRAVED BAKELITE NAMEPLATES FOR ALL MECHANICAL EQUIPMENT
INCLUDING TENANT'S NAME AND SPACE NUMBER. LETTERS SHALL BE 2" HIGH OR
AS REQUIRED BY THE LANDLORD.
16. ALL FABRICATED COMPONENTS (CONTRACTOR OR MANUFACTURER) OF THE
OUTSIDE AIR, SUPPLY AIR, RETURN AIR AND EXHAUST AIR SYSTEMS SHALL BE
CONSTRUCTED AND INSTALLED AIR TIGHT. THE INSTALLED SYSTEMS SHALL BE
PRESSURE TESTED AS REQUIRED.
17. NOT USED.
18. FURNISH TWO (2) COPIES OF AS BUILT DRAWINGS OF THE A.C. SYSTEM
TO THE
OWNER FOR REVIEW AND APPROVAL, OR SUBMIT A LETTER TO THE OWNER
CONFIRMING THAT THE SYSTEM WAS INSTALLED AS PER PLANS AND SPECIFICATIONS.
19. ALL WORK AND EQUIPMENT SHALL BE CLEANED TO THE SATISFACTION OF THE
OWNER BEFORE TURNING PROJECT OVER TO THE OWNER.
20. SEAL ALL PENETRATIONS THROUGH WALLS, CEILINGS, FLOORS, ETC. SO THAT
THEY ARE AIR, WATER AND FIRE TIGHT.
21. FURNISH AND INSTALL ACCESS PANELS FOR ALL CONCEALED EQUIPMENT, FIRE
DAMPERS, PIPING VALVES, CLEANOUTS, ETC. ACCESS PANELS SHALL BE OF
SUFFICIENT SIZE TO PROVIDE ADEQUATE WORKING CLEARANCE AND ACCESS.
22. FURNISH ALL MATERIAL AND EQUIPMENT AS SPECIFIED, EXCEPT WHERE SPECIFIC
APPROVAL FOR SUBSTITUTION IS GIVEN BY THE TENANT.
23. PROPOSAL SHALL BE BASED ON SPECIFIED MATERIAL AND EQUIPMENT. IN
ORDER TO PROMOTE COMPETITION, HOWEVER, BIDDERS ARE ENCOURAGED TO SUBMIT
ALTERNATE PROPOSALS ON ANY ALTERNATE MATERIALS AND /OR EQUIPMENT THEY
WISH TO PROPOSE, INCLUDING ANY PRICE CHANGES EFFECTED BY ACCEPTANCE OF
ALTERNATES.
24. COST OF ANY CHANGES REQUIRED BY OTHER TRADES DUE TO SUBSTITUTION CAF
ALTERNATE EQUIPMENT SHALL BE INCLUDED IN THE ALTERNATE PROPOSAL.
25. ALTERNATE PROPOSALS WILL BE ACCEPTED OR REJECTED BEFORE ISSUANCE OF
CONTRACTS. NO CHANGES WILL BE ALLOWED AFTER THE CONTRACT IS SIGNED.
ANY UNAUTHORIZED CHANGES TO THE DESIGN AND LAYOUT MAY BE REQUIRED TO BE
REMOVED AT CONTRACTOR'S EXPENSE IF DEEMED NECESSARY BY THE ARCHITECT,
ENGINEER OR OWNER'S REPRESENTATIVE.
26. VERIFY LOCAL CONDITIONS AT SITE.
27. COMPLY WITH ALL APPLICABLE CODES.
28. SECURE AND PAY FOR ALL REQUIRED PERMITS.
29. SEE REFLECTED CEILING PLAN FOR EXACT LOCATION OF CEILING GRID, LIGHT
FIXTURES, ETC.
30. ALL INSULATION MATERIALS, INCLUDING, BUT NOT LIMITED TOO DUCT INSULATION
AND PIPING INSULATION SHALL HAVE A FLAME SPREAD RATING OF 25 OR LESS (ON
THE FLAME SPREAD TEST SCALE) AND SMOKE DEVELOPMENT OF 50 OR LESS (ON
THE SMOKE TEST SCALE) OR AS DEFINED BY NFPA 255 STANDARD METHOD OF
TESTING OF SURFACE BURNING CHARACTERISTICS OF BUILDING MATERIALS, LOCAL
CODES AND LOCAL AUTHORITIES HAVING JURISDICTION.
31. DIELECTRIC UNIONS SHALL BE USED TO CONNECT DISSIMILAR METALS OR METAL
PIPING SHALL HAVE METAL CONNECTIONS ON EACH END THREADED TO MATCH THE
ADJACENT PIPING. METAL COMPONENTS SHALL BE SEPARATED BY A NYLON
INSULATOR TO PREVENT CURRENT FLOW BETWEEN DISSIMILAR METALS. UNIONS
SHALL BE SUITABLE FOR THE SYSTEM OPERATING PRESSURES AND TEMPERATURE
WELD TYPE: ASTM A -234.
MECHANICAL WORK NOTES r- AIR FILTERS
1. ON THE DAY OF STORE CONSTRUCTION COMPLETION/TURNOVER, THE AIR
CONDITIONING EQUIPMENT FILTERS, IF ANY, (WHETHER NEW CONSTRUCTION OR
EXISTING) SHALL BE REPLACED WITH NEW FILTERS.
•
u e
•
•G •
Z
OF
0 2
i�
� V
�w
qp
O
0 w
J/►T s W • . ,S/n/14
y V U y
'JOi IRJi 1"15
DRAWN:. STAB
�NEC01t.* CM
• Gu• •
fill;
�r
L?
32fi
r
C
C
F'1'i01JECT COmt"TICIN
(ADDTC(H
W 0/K M IR"I s E s m- Oil)1N -Silo
091160" Cr OWU FAX ("CM -56W
W
W
0 j ,�..
4j...R,
uj LL
JZ W cr
V
co
>
cn� N
coW'ctr►
CL 0 0 z . CC r
0 cn W
CLr w 0 U Q
co
(CL Q
F_ Lc) _ (n IF
r 'r
r
I rO
STORE NUMDER
z
A.C. UNIT REFURBISHMENT NOTES
1. BASE BID SHALL INCLUDE A DETAILED FIELD INSPECTION OF THE EXISTING A.C.
EQUIPMENT TO DETERMINE ITS CONDITION AND COSTS TO PERFORM MAINTENANCE
SERVICE ON EXISTING UNITS AS REQUIRED TO GUARANTEE PROPER OPERATION,
CONSISTING OF, BUT NOT LIMITED TO, THE FOLLOWING:
A. CHECK AND ADJUST BELTS. REPLACE IF REQUIRED.
B. CHECK FAN FOR PROPER OPERATION. REPLACE BEARINGS IF REQUIRED.
ISSUE
C. CHECK CHILLED WATER PIPING SYSTEM FOR LEAKS. REPAIR AS REQUIRED.
'A' -ISSUE LL. RID, PERMIT
D. CHECK CHILLED WATER CONTROL VALVE. REPLACE OPERATER IF REQUIRED.
DATE 3/u/14
E. CLEAN COIL SURFACE IF REQUIRED.
'r -ISSUE
F. REPLACE FILTERS.
DATE
G. CHECK AND ADJUST CONTROLS.
'c'-DATE E
H. REPAIR ANY RUSTED AREAS ON UNIT CASINGS. REPAINT AS REQUIRED.
I. ADJUST AS REQUIRED TO DELIVER AIR QUANTITY SHOWN OR CALLED FOR.
'D`-DATE
2• SUBMIT AN ALTERNATE PROPOSAL ACCOMPANYING BID TO REPLACE ALL EXISTING
EQUIPMENT, WHICH WILL BE CONSIDERED BY THE TENANT IF THE EQUIPMENT IS
T-IS E
DETERMINED TO BE IN NEED OF REPLACEMENT AFTER THE INITIAL INSPECTION..AI""11""` 411,
ALTERNATE PROPOSAL SHALL BE COMPLETE, INCLUDING LAE' R�..•PENN ,,
THE JOB SITE.
SHEET TITLE
RIGGING COSTS (IF ANY), ETC. + +' y�(,EIVS•, *-
, .�
No 5
WAU
�* r
'. 13% ST A E OF
• r
•��:
a \0.' �`'��•
INN
M1.0
J/►T s W • . ,S/n/14
y V U y
'JOi IRJi 1"15
DRAWN:. STAB
�NEC01t.* CM
• Gu• •
fill;
�r
L?
32fi
r
C
C
F'1'i01JECT COmt"TICIN
(ADDTC(H
W 0/K M IR"I s E s m- Oil)1N -Silo
091160" Cr OWU FAX ("CM -56W
W
W
0 j ,�..
4j...R,
uj LL
JZ W cr
V
co
>
cn� N
coW'ctr►
CL 0 0 z . CC r
0 cn W
CLr w 0 U Q
co
(CL Q
F_ Lc) _ (n IF
r 'r
r
I rO
STORE NUMDER
ISSUE
'A' -ISSUE LL. RID, PERMIT
DATE 3/u/14
'r -ISSUE
DATE
'c'-DATE E
'D`-DATE
T-IS E
DATE
SHEET TITLE
FLOOR PLAN
MECHANICAL WORK
WAU
1 /4'x-1' -0''
SHEET NUMBER
M1.0