05-1487-0042_
- r
j y
_ I
35' -01
CODE COMPLIANCE NOTES
SHOWER COMPARTMENT FINISH:
THE SHOWER COMPARTI" 1ENT MUST BE
FINISHED IN SMOOTH, IMPERVIOUS MATERIALS
TO A MINIMUM HEIGHT OF -10 INCHES.
TYPICAL PARTITION
I- TYPICAL NON LOAD BEARING INTERIOR
PARTITION TO BE 25 GA. METAL STUD AT 1(o"
O.C. WITH 2 "X4" WOOD STUDS AT EACH SIDE OF
DOOR OPENINGS.
PARTITION REINFORCEMENT:
- BEHIND WALL. HUNG PLUMBING
FIXTURES AND WALL CABINETS PROVIDE 20
GAGE STUDS Q I (o" O.C. MAX. IN ADDITION,
BLOCK -UP W/ 2"X4"
WOOD.
- VERTICALLY AND HORIZONTALLY AS
REQUIRED TO FACILITATE NAILING.
; AFETY GLASS AT HAZARDOUS LOCATION
HE FOLLOWING LOCATIONS SHALL HAVE CAT II SAFETY GLASS PASSING
:PSG 16 -CFR TEST:
I GLAZING IN ALL SWINGING AND SLIDING DOORS.
. ALL GLAZING IN SHOWERS AND TUB ENCLOSURES FOR THIS PROJECT:
ANY GLAZING PANELS OTHER THAN THOSE DESCRIBED ABOVE THAT MEET
ALL OF THE FOLLOWING:
A. EXPOSED AREA OF PANE GREATER THAN 3 5Q. FT.
B. BOTTOM EDGE LE55 THAN 18" FROM THE FLOOR.
C. TOP EDGE GREATER THAN 36' FROM THE FLOOR.
D. ONE OR MORE WALKING SURFACE WITHIN 36" HORIZONTALLY
FROM THE PLANE OF GLAZING.
GLAZING IN RAILINGS - IF ANY NA,
GLAZING ENCLOSING INDOOR SWIMMING POOLS AND SPAS. N.A.
NOTE:
ALL EXTERIOR GLAZING IN THIS PROJECT WILL BE IMPACT RESISTANT.
ONSTRUCTION NOTES:
ROOF SHEATHING:
1. RO F SHEATHING SHALL eE MIN. 19/32 AND SHALL BE CONTINUOUS OVER TWO
SU PORTS. THE FACE GRAIN SHALL BE PERPENDICULAR TO THE SUPPORTS, NAIL SPACING
AT PANEL EDGE AND INTERMEDIATE SUPPORTS AND GABLE ENDS SHALL BE 4" O.C.
2. AL PANELS SHALL BE SUPPORTED WITH MD COMMON NAILS.
INSULA(ION:
1. IN ULATION SHALL BE AS FOLLOWS:
A. ALL EXTERIOR WALLS OR FIRST FLOOR SPACE TO HAVE R 4.1 PAPER BACK FOIL.
B ALL CEILINGS OR ROOF RAFTERS TO HAVE R -19 BATTEN INSULATION.
C. INSULATION OF BUILDING ENVELOPE SHALL BE CONTINUOUS.
D. REFER TO FLORIDA STATE ENERGY CODE FOR ANY ADDITIONAL INSULATION
ADDITIONAL INSULATION REQUIREMENTS, REFER TO MECHANICAL DRAWINGS FOR CHECKLIST
CHECKLIST.
GENERAL CONSTRUCTION:
1. IN ERIOR PARTITIONS TO BE 25 GA. METAL STUD AT 16" O.C. W /2X4 WOOD
S UDS AT EACH SIDE OF DOOR OPENINGS.
2. ALL INTERIOR PARTITIONS TO HAVE 1/2° GYPSUM BOARD. ALL BATHROOMS AND AREAS
S BJECT TO HIGH MOISTURE SHALL HAVE DUROCK BOARD OR GREENBOARD WHERE
N TILE IS INSTALLED.
3. ALL FRAMING SHALL BE DONE IN A WORKMAN -LIKE MANNER BE SKILLED LABOR.
ALL NAILING AND CUTTING OF WOOD STRUCTURAL MEMBERS SHALL BE IN COMPLIANCE
W CHAPTER 29 OF THE SFBC.
4. ALL LUMBER IN CONTACT WITH MASONRY OR CONCRETE SHALL BE PRESSURE TREATED.
5. PROVIDE 4" WIDE CONTINUOUS MESH UNDER EAVES FOR ATTIC VENTILATION.
6. IN TALL MILLWORK ACCURATELY WITH TIGHT JOINTS AND TRUE SURFACES WELL SANDED
A D FREE OF DEFECT.
7. AL INTERIOR AND EXTERIOR DOORS TO HAVE TWO COATS OF TOP QUALITY LATEX SEMI- GLOS.
EN MEL PAINT. ALL WALLS TO RECEIVETWO CATS OF EGSHELL PAINT. ALL INTERIOR DOORS
TO I RECEIVE TWO COATS OF SEMI -GLOSS PAINT,
)l FIRST FLOOR PLAN
z
(5
U)
ui
b
Lu
WNC4�
�
1a
W
Q
i