02-830-058C�
i`
i+
i
i
r�
a
I
a
3
t
7.
0
11111
I�
to
0
Vf
M
v
1 .
6A.3.7 Stud Wall Framing:
A. Studs spaced 16 inches on center, or as detailed.
B. Horizontal blocking at the midpoint of each stud wall not over
4' -0" apart vertically.
6A.3.8 Joist' Cross-Bridging: Cross- Bridging shall be made of 1" x 3" strips.
not over 81-0" between rows.
6A.3.9 Lintels: Unless otherwise noted spans up to 4' -0" - two 2x4's; 4' -0"
to 5' -6" - two 2x6's; 5' -6" to 7' -0" - two 2x8's; over 7' -0" - 2x10's.
6A.3.10 Fire Retardant Treatment: All lumber indicated on the drawings as fire
treated shall be treated in accordance with AWPA C278..
SECTION 6B FINISH CARPENTRY AND MILLWORK
6B.1 GENERAL
6B.1.1 Scope:
A. Furnish and install all finish carpentry and millwork on the
drawings or specified herein.
Be Wood doors, finish hardware door grilles shall be installed under
this section. _
6B.1.2 Shop Drawings: Submit ship drawings to Winn -Dixie for approval prior
to any fabrication.
6B.1.3 Delivery and Storage:
A. Deliver finish lumber or millwork to the job after all wet trades
are complete and building is closed in.
Be Store materials off the &LvuzU..
C. Stack doors and plywood in accordance with the manufacturer's
instructions.
6B.1.4 Industry Standards:
A. Grading of Lumber: American Lumber Standards Committee, Simplified
practice Recommendation $-16.
Be Grading of Plywood: U. S. Product Standard PS 1 -66.
C. Wood Doors: Commercial Standard CS171, latest edition, as
published by the U. S. Department of Commerce.
6B.1.5 Reference to'the Drawings:
A. Refer to the Drawings for material items and requirements not
specified.
Be 'The drawings may require material items which differ from these
specifications. In such cases, the requirements of the drawings will
take precedence.
6B PRODUCTS
6B.2.1 General Requirements: All lumber and plywood shall bear the grade and
trademark under which it is produced and a mark of mill identification.
A. Sizes and Patterns: Lumber shall be surfaced 4 sides. Worked
materials shall be S. P. R. - R -16 unless otherwise indicated.
6B.2.2 Moisture Content: Finish lumber shall be seasoned and shall have not
over 15% moisture content.
6B.2.3 Door Frames: White pine, Larch, or Cypress; Grade "B" or better.
6B.2.4 Trim: Grade "B" or better Cypress, Larch, or White pine. Decor trim
shall be Western Cedar consisting -of select pieces. which match in color
before application of finish.
6B.2.5 Plywood:
A. Exposed both sides: A -A Int. DFPA.
Be Exposed one side: A -D Int. DFPA.
C. Exterior type to be used if indicated on the drawings.
6B.2.6 Wood Dorrs: All wood doors shall meet or exceed Commercial Standard
CS171, latest edition, as published by U. S. Department of Commerce.
A. Interior wood doors shall be solid core.
Be Doors shall have face veneers of paint grade birch unless-
otherwise indicated on the drawings.
6B.2.7 Fastening Devices: Where required, shall be noncorrosive of types and
sized sufficient to rigidly secure members in place.
6B.2.8 Marlites: where shown on drawings, "Marlite" shall be installed per -
manufacturer's recommendations.
DIVISION 7 '
L AND MOISTURE PROTECTION
SECTION 7A BUILT -UP ROOFING. ROOF INSULATION, FLASHING AND SHEET METAL
7A. 1 GEIJERAL
7A.1.1 Scope: Furnish all labor, materials and equipment necessary to apply
and install BUILT-UP ROOFING, ROOF INSULATION, FLASHING AND SHEET METAL
work indicated on the Drawings as specified herein. _
7A.1.2 Requirements: Roofing contractor must be approved by roofing material
manufacturer and. shall install his work in accordance with printed
.recommendations of the manufacturer. Any work installed that is not in
accordance with the requirements of the manufacturer of the roofing
material shall be corrected at the expense of the roofing contractor.
_t T - -L. 4- .C. -_.- " -44 dr all rnni e%rnfne+va ci,_,l l
be carefully checked. It shall be the ' roofer "s responsibility to
determine whether or not the roof deck and perimeter areas are
in satisfactory condition to receive the new roofing. Application of
insulation constitutes full acceptance of the roof deck surfaces by the
roofer and manufacturer of the roofing :materials. Consideration must
IM b.1.YC" UV UU= WJI 0=,_l.i=s tw.A4% VVA4%= %;&UX CLU%% UWW t3=v 110W WV1]L WXXX
be joined to provide a complete watertight roofing surface.
7A.1.4 Existing Conditions: The Contractor shall hire an independent roofing
consultant to inspec existing roofing and flashing conditions
immediately after signing construction agreement with Winn -Dixie or
Landlord. Report shall be provided to Winn- Dixie, Landlord, General
Contractor aned Roofing Sub- Contractor.
7A.2 PRODUCTS
7A.2.1 Roofing Materials: Shall consist of four (4) plies of glass -fiber
sheets and uniform top coating embedded with gravel.
a. Celotex Specifications (Ztt -.T'D SGW&449,4
b. 44VV . Specifications shall be No. 4G/-C.
c. Owens /Corning Specifications (45�t Aon ..ate• CII&Z44*)
d. Glass Fiber sheets shall meet requirements of ASTM D -2178, type VI.
7A.2.2 Fci id Roof Insulation: Shall be two layers of Celo one
p dyer over deck 2.8 inches of
Hy- Therm R --2 ue second layer 1/2 er -
-2 i� .Zol L17C DYE
7A.2.1 Gravel: vel conforming to AST. DIS
rate of application 400 s
7A.2.4 Plumbing Shields: 41bs. sheet lead furnished by plumbing contractor
and installed by roofing contractor.
7A.2.5 Base and/or Wall Flashing:
A. Celotex "AB -20 ".
Be Manville "DYNAFLEX° ,
C. Owens/Corning "Derbigum" S.P.
7A.2.6
Counter Flashings: Galvanized iron, 24 gauge.
dissimilar materials from contact by neporene gaskets or bituminous
7A.2.7
Pitch Pans: Galvanized iron, 24 gauge. Fill with asphalt.
coating.
7C.1.5
APPLICATION AND GUARANTEE:
7A.2.8
Gravel Stops: 26 gauge galvanized iron.
• S
SECTION 8
A. All sealants shall be installed by approved applicators.
7A.2.9
Gutters and Downspouts: 26 gauge galvanized iron.
Be Guarantee: Written guarantee shall be provided for a period of not
7A.3
EXEC'UTI
less than. five (5.) years from date of acceptance. Contractor shall be
responsible, during guarantee period, to repair and replace defective
7A.3.1'
Uplift: Roofing installation shall be installed in conformance with
work and other work damaged thereby at no additional cost to Owner.
8D.1 GENERAL
requirements of local code where project it to be constructed.
7C.2 PRODUCTS
7A.3.2
APPLICATION OF RIGID ROOF INSULATION:
1. Locksets - Schiage, Corbin, Russwin, or Yale 8
8D.1.1 S
A. Store and protect insulation in conformance with manufacturer's
7C.2.1
SEALANT TYPE 1:
printed instructions.
A. SEALANT MATERIAL: A one part silicone rubber sealant.
Be Do not apply any damp or wet insulation.
2. Butts - Stanley or Hager. Non - removable pins for exterior doors. d
Be SEALANT MANUFACTURER: General Electric Company sealant, or Dow
drawings, and as specified herein.t
Corning 780 Building Sealant.
C. Apply no more insulation than can be covered in a days work.
Protect insulation from moisture.
C. Type 1 sealant shall be used for porous materials, concrete, brick
D. Size, spacing and installations of metal fasteners shall be in
etc'
conformance with manufacturer's printed instructions and for uplift
7C.2.2
SEALANT TYPE 2:
•4. Door Pulls, Push Plates, Flush Bolts, Stops and Holders - Russwin, 8
requirements where project is to be located.
Approved manufacturers:
A. SEALANT MATERIALS: A one part butyl rubber sealant permanently
7A.3.3
Application of Built-Up Roofing:
_
flexible.
A. Install only when temperature is above 40 degrees F.
Be SEALANT MANUFACTURER: R.I.W. Butylseal, Dap Butyl -Flex, or
Be Apply built -up roofing finish in a continuous operation over any one
Hornseal: '
area. No "Phasing" as defined by Celotex.
Cipco. 1
C. Type 2 sealant shall be used for glass, aluminum, ceramic, plastic,
1. Pettsburgh -Plate Glass
C. Where splicing is necessary due to carry over, lay cover ply and mop
etc.
well in place. Cover ply shall be removed when starting again.
7C.3 EXECUTION
D. Prevent traffic from : inz built -up roofing.
70.3.1
Apply rimer and sealer wb r :-c --t em cr specified in etrict ac cori -o -Ce
with manufacturer's recommendations.
E. Attach base sheet to substrate in accordance with roofing
8A.3 EXECUTION: Installatin of hardware and accessory items called for under 3
manufacturer's specifications.
3. Mississippi Glass
F. Lay no more rigid insulation than can be covered in a days work.
SECTION 7D
- BUILDING INSULATION
Protect insulation from moisture.
7D.1 GENERAL
this section shall be installed under Section 68.
7A.3.4
Installation of Bituminous Base Flashing:
7D.1.1
SCOPE: The work in this section includes all insulation in ceiling and
A. Install in conformance with manufacturer's printed instructions.
walls as specified or called for on the Drawings.
7D.1.2
SAMPLES: Submit samples of building insulation when requested by Winn
7A.3.5
Metal Flashing and Accessories:
Dixie.
A. Install metal counter flashing and accessories as specified and
7D.1.3
IDENTIFICATION: All J=ulati.oa material ahall bo properly identified
indicated on Drawings.
on the package with the manufacturer's name and R value.
B. Shaping trimming and hand seaming to be done with the proper sheet
7D PRODUCTS
metal working tools, with allowances for expansion and contractions
•
to avoid buckling and/or fullness.
7D.2.1
BLANKET INSULATION: Provide aluminum foil fiberglass insulation in
C. Install allbase flashings, counter flashings, and pitch pans for all
conformance with thickness or "R" value indicated on drawings, if not
ducts, pipes, conduit, supports, etc., that run through the roof
indicated use R -19. Where there is existing insulation; add the
deck.
required fiberglass batt insulation to reach a minimum R -19.
D. Install a cricket to deflect roof water around all roof mounted
7D.2.2
FOAM INSULATION: For exterior concrete masonry walls insulation shall
equipment and penetrations larger than 12' inches wide.
be "Core -Fill" 500 as manufactured by Tailored Chemical Co., Hickory,
Glass shall comply with Federal Specifications DD-G -451a.
N:C. A "II" value of 0.05 is obtained on a 12" concrete block wall
7A.3.6
Flashing Plumbing Vents Through Roof: Vents through roof shall be
exposed both sides and a "U" value of 0.06 is obtained on a 8" concrete
flashed using 4 lb. lead not less that 20" x 20 ". Roof flashing flange
the drawings and as specified herein. 8
block wall exposed on inside and faced on exterior with 4" brick.
Glass for Storefront: Shall be a total of 1" thick, made up of 1/4"
shall be secured with appropriate nails. The metal flashings shall be
coated with hot bitumen, then imbed a strip of felt, approximately 4 "7p
3 EXECUTION
over the nail course. The first felt shall-be coated with bitumen,
8B.1.2 Applicable Standards: Steel doors and frames shall be manufactured t
tempered when within 4' of a door,
then imbed a second.strip of felt 6" wide, covering the first layer.
7D.3.1
Blanket insulation shall be neatly placed, not squashed together and
according to the Steel Door Institute "Recommended Specifications for
Over this apply a final coat of bitumen, then imbed the surface grave.
joints overlapped in location indicated on the Drawings, and over any
'
existing areas not meeting an R-19 value.
7A.3.7
Instal n-sf .-Gravel Stops:_
7D.3.2
The complete core in all exterior hollow-core concrete masonry units
8B.1.3 Storage: Doors -and frames shall be stored under cover on the building 8
A. Install gravel stop as drawn, or-with drive screws spaced
Glass for Meat Cutting Room, Office (and Pharmacy) if included in store
shall be filled, from. top of concrete footing to top of masonry, with
approximately 4 inches on center. Do not face nail.
"Core -Fill" 500 insulation. Apply in strict conformance with
design): 1/4" polished safety plate.
manufacturer's printed instructions by Certified Applications.
B. Gravel stop joints shall be spaced 1/2" covered with 6" wide joint
damage. V
covers.
SECTION
7E - DAMPROOFING
C. Two layers of 15 lb. felt shall then be set over flange of gravel
73.1 GENERM
8D.2.5 G
stop.
7E.1.1
Apply a continuous damproofing coating over exterior face of interior
D. Provide expansion and construction joints as required.
wyte of masonry veneer walls.
7A.3.8
Gravel: _
7E.1.2
Apply a continuous clear water repellent coating over exterior face of
all non - painted concrete masonry unit.
A. Over entire roof surface apply uniform top coat of hot asphalt at
rate of 60 lbs. per square.
7E.2 PRODUCTS
Be While asphalt is hot embed 400 lbs. min. per square of rounded pea
7E.2.1
"Flat -top Fiberated Emulsion" as manufactured by Celotex, "712-B Spray
gravel surfacing.
Mastic" as :manufactured by J & P Petroleum Products, or "Hydrocide 700
Mirrors: .
B" as manufactured by Sonneborn Building Products, Atlanta, GA.
C. Follow roofing manufacturer's printed instructions for gravel
A. Toilets: Xirmi -Caioy M2114, 5
surfacing installation.
7E.2.2
Clear water repellent shall be VIP Ombrella No. 9100 VIP Enterprizes,
5979 N.W. 151 STR
primer. _
• B
Inc., Miami. FL. "White Roc as manufactured by Sonneborn, Atlanta,
7A.3.9
AND DOWNSPOUTS: Shall be prefabricated 26 gauge galvanized
GA., or "Waterban 25" as- manufactured* by Lambert Corporatian, - Orlsnao,
8B.2.3 Doors: a
steel. 'Manufacture in 10' -0" lengths with joints lapped. Turn out at
as manufactured by Pittsburgh Plate Glass Co., or Libbey -Owens -Ford. M
FL.
splash blocks. Hold in 1" clear of the wail with G. I. straps.spaced
M"I DES. FLA. 33
as required.
7E.3 EXECUTION
7A.3.10
PREFABRICATED MANSION JOINT COVER:
7E.3.1
"Flat -Top Fiberated Emulsion" shall be applied to exterior face of
D. Solor bronze plexiglass mirror 3/16" thick laminated to 9/16" medium w
interior wythe of masonry veneer walls. Coating shall be applied at
A. Provide expansion joint shield as manufactured by Celotex or
cleared at jambs and heads, 1/4" clearance at meeting edges of pairs d
rate of 2 gal. /100 sq.ft. minimum per coat. Two coats required.
density fiberboard.
approved equal.
Apply by brush or. spray continuously from top of concrete footing to
of doors, and 1/4" clearance at bottom.
top of masonry. Second coat applied at right angles to the first coat
Be The expansion joint cover shall be furnished in lengths of 10 feet
no less than 24 hours after first coat applications.
or longer with materials supplied by manufacturer and install in
'
8D.3.1 I
accordance with printed instructions.-
7E.3.2
Clear water, repellent shall be applied over all non painted concrete
�.
C. Internal Construction: Construction of the door shall be in t
masonry units. Apply by brush or roller from top of concrete footing -
7A.3.11
CLEANING: The Contractor shall exercise' extreme caution in handling of
accordance with the manufacturer's standard practice. Except exterior
to top of masonry.
Install Sales Area mirrors as indicated on the drawings.
bitumen, protecting surrounding work at all times. Excess materials
78.3.3
All products applied in strict accordance with manufacturer's printed
doors shall be solid core. 8
shall be completely removed from surrounding work.
_
instructions.
SECTION
7B - MECIRM BARRIER
DIVISION 8 - DOORS.-WINDOWS, GLASS
7B.1 GENERAL
SECTION
8A FINISH HARDWARE .
rv.s.a
000ra. :.��_a_ -s _ ..a -.L _s, um%mv ur uanno R-A-P TFN indicated on the
Drawings or as specified herein.
8A.1 GEN
tAI
7B.2 FRODIICTS
8A.1.1
SCOPE: Furnish finish hardware as shown, specified, or required.
--_ 7B
"y S o " Polyethylene sheeting, as manufactured by Visqueen Division,
8A•1.2
General: It is intended that the following list of hardware or
-2_1
E rporation, or equivalent..
narawar-e scneuuuva on use �n...u.aa .....o. __,1 2._..._s - -_ 2 L-
complete the project. The Contractor will be required to furnish and
a. THICKNESS: Under concrete floor slabs - 6 mile
install all hardware required to complete the project, whether or not
it is listed herein. This contractor shall be fully responsible for
7B.2.2
JOINT SEALANT: FOSTER 18208 adhesive or Pitts- corning "INSULKASTIC "•
checking the details, in order that all items of hardware shall fit
Apply per manufacturer's printed instructions.
properly.
7B.3 EXECUTION
Contractor: Provide a competent Hardware Consultant (AHC or
equivalent) to service the hardware at the project, and to approve its
7B.3.1
UNDER CONCRETE FLOOR SLABS: Spread sheeting smoothly over sub -grade
installation. All items shall be installed in the best manner and
and turn up the full thickness of the slab at the perimeter. Install
function perfectly.
the minimum end and side laps of 6" and seal with Joints sealant the
entire lap.
8A.1.3
Schedule 4 copies of the typewritten schedule to Winn -Dixie for
approval.
SECTION
7C - SEUM
BA. 1.4
Hardward Location:
7C.1 GENERAL
Hinges - Top hinge - 7" below head rabbet
7C.1.1
SCOPE: Furnish and install all SEALANT indicated on the Drawings as
specified herein.
Bottom hinge - 7" above finished floors
7C.1.2
APPROVAL: Submit proposed product to Winn Dixie for approval before
Middle hinge - equally centered between top and bottom.
using. Do not install materials until approved.
•
Locksets - Cyl. deadlocks - 44" above finished floor to center.
7C.1.3
GENERAL:
Knob locks - 36" above finish floor to center.
A. Refer to the Drawings for the Locations of the various types of
Exit Devices - 40 -1/8" above finish floor to center of lock housing.
sealants required.
Be Seal all openings, expansion joints and fleshings and all other
Door Pulls - 40" above finish floor to center.
places necessary to prevent the entry of storm water.
Push Pietas - 48" above finish floor to center. Furnish cutout where
C. Sealant work specified under this section shall, in some cases, be
required.
accomplished under other sections of the specifications.
8A•1.5
Guarantee: Contractor shall guarantee, in writing, all materials for a
D. Installation of work indicates acceptance of job conditions.
period of two (2) years after acceptance by Winn- Dixie. Contractor
Contractor shall be responsible for satisfactory results.
shall replace, at his own expense, including labor, any items of
hardware which prove defective within this period.
7C.1.4
HEALTH PRECAUTIONS: Observe precautions recommended by the
manufacturer.
8A.1.6
Keys and Keying:
A. Provide two (2) keys for each lock.
Be Do not master -key except as otherwise indicated on drawings .
odi A altgi1331u1iri tri3A IIo trim betsraen caution of
i
sm
8B.2.4 Frames: A. UDC continuous an ze , Q
mirrors.. Butt edges. Do not used rosettes. Use long lengths, 4'-0" O►
A. General: Frames for doors shall be .combination buck, frame and minims and 8' -0" maximum.
trim type, according to drawings.
B. Adjust tilt of mirrors to the scale optical plane with a minimum of
Be Frame Thickness: The sheet metal frames shall be 14 gauge steel distortion at joints.
for exterior frames and 16 gauge steel for interior frames. 8D.3.3 Install toilet mirrors above each lavatory 6' -0" above finish floor to 0) N
C. Frame Anchors for Wall Conditions: Provide for a mu'dmum of three top. M
anchors per jamb, 18 gauge steel. -
8D.3.4 Cleaning: At completion, the glass an plexiglass shall be cleaned of QQ
D. Floor Anchors: Provide 16 gauge anchors at the floors. all foreign matter.
CL
8B.2.5 Fire Doors and Related Frames: fire doors and frame assembly shall be SECTION BE - AUTOMATIC DOOR OPERATORS O
in accordance with the ASTM designation E- 152 -41. The label shall LL
Indicate the fire test rating for the door. SE.1 GENERAL: Furnish and install all automatic door operators indicated on the
drawings and as specified herein. W
8B.2.6 Hardware: J
8E.2 PRODUCTS >
A. Doors and Frames shall be reinforced, drilled and tapped to receive
mortised hinges, locks, latches, flush bolts and concealed door closers 8$.2.1 Automatic door operators shall be type as indicated on the drawings. 4
as required. i_ U
8E.2.2 Include all controls and equipment as required for a complete •
Be Hardware shall be field applied. installation.
C. Reinforcings and preparations shall be located as shown on Table V 8E.2.3 Finish of all aluminum shall be 140 Dark Bronze.
of the standard Door Institute "Specifications for Standard Steel Doors cc
3 EXE M IQN j
subect to individual manufacturer's 8E. D
and Frames (S.D.I. 1001, � � O
variation.
8E.3.1 Install all operators, controls and equipment, accessories, etc., in U
8B.3 EXECUTION strict accordance with manufacturer's details and instructions.
Q O
8B.3.1 Frames shall be installed plumb, rigid and in true alignment. 6E.3.2 Leave installation clean, properly adjusted, and in full and complete =
operative condition. 3:
8B.3.2 Doors shall be fastened for maxim= effectiveness and appearance. OF. IL ROLLING DOORS
8B.3.3 All exterior doors shall be weather stripped. L!J
W
8F.1.1 See Drawings for type of door and location.
0
SECTION 8C - ENTRANCES. AND STOREFRONTS 8F.1.2 Provide all locking hardware so that a padlock may be provided by (9 C>
AN
�C.1 GENERAL _ Winn -Dixie and door will be secured. C0
LU
8C.1.1 Scope: furnish and. install entrances and storefronts indicated on the 8F.1.3 Install door in strict conformance with manufacturer's printed C1
drawings-as specified herein. instructions. cc
O
8C.1.2 Shop Drawings: Submit shop-drawings to Winn- Dixie. DIVISION 9.- FINISHES ~
01)
8C.1.3 Cleaning: Clean and polish all work at the completion, as recommended SECTION 9A -LATH AMID STUCCO
by the manufacturer.
8C.1.4 Guarantees: 9A.1 GE2IERAL
9A.1.1 Scope: Furnish all labor, materials and equipment required to complete ;
A. Guarantee shall include water tightness and defects due to all LATH AM PLASH work indicated on the Drawings or as specified ;
materials or workmanship. herein.
Be Guarantee over door closers for two (2) years. Guarantee shall be .�
in writing. 9A.1.2 Delivery and Storage: Deliver all materials in their original (`�
packages, bearing name of the manufacturer, and store materials off the
floor.
8C.1.5 Approved Manufacturers: Equivalent sections of other manufacturers may %0
be substituted. contractor shall submit data as required to give 9A.1.3 Mix. Mix all stucco as recommended by the manufacturer.
evidence that the requested substitution is equivalent. Storefront'
actions shall be as manufactured b the Amarlite Corporation, Kawneer
s y 9A.1.4 Finish Texture: Shall match existing finish or shall be white with a '''•
Company, or Pittsburgh Plate Glass Company. light sand finish.
N
8C.2 MATERIALS:
ALS.
9A.2 PRODUCTS Q`
8C.2.1 Products specified as standard of quality are manufactured by Kawneer
-...._ T.... 9A.2.1 A. Main Runners: 1 -1/2" cold - rolled steel channels.
• S. l,?OSS 1lIrrlllg: J/4 w2.a- ivaaca owns v1s.a......i�_ ". ,;
8C.2.2 Extrusions: 6063 -T5 aluminum alloy meeting ASTM B221 -79a. C. Wire Hangers: No. 8 gauge.
D. Tie Wire: No. 16 gauge.
• - d h fob ' 4 d from alvanized steel h
8C.2.3 Aluminum Sheet: 5005 -H34 aluminum alloy meeting ASTR B209 -80, minimum E. Aetal Lath: Diamon mes rice e g •
0.050" thickness. F. Casing Beads: Square end, sized to full stucco thickness.
U. *2WLPa M.LVU UV.LU% -0i 0AK-VFQ w Goal oU-- ••-•.Aw..._�, sa_
8C.2.4 Fasteners: All fastening devices shall be stainless steel; countersink 75 at 10' -0" O.C. if not indicated on drawings.
exposed fasteners; match entrances and storefronts in color. All
fasteners shall be tamper proof. 9A.2.2 A. Portland Cement: Type I, non staining, ASTK C -150. DRAWING TITLE
Be Lime: ASTM C -206, Type S, Double Hydrated. c
J
8C.2.5 Finish: All exposed aluminum surfaces including brake metal shall have C. Masonry Cement: ASTM C -91, Type II. SPEC l
architectural Class 1 anodic coating with integral color conforming to . D. Sand: Clean, well- graded from coarse to fine.
Aluminum Allocation standard AA -M12 C22 A42/44. Color shall be #40 E. Water: Potable
Dark Bronze. F. Finish Coat: Factory pre-mixed white stucco with light sand finish.
8C.2.6 Storefront Sealant: Non - skinning type meeting NAAMM standards 5C -1.1. 9A.3 APPLICATION OF STUCCO
color to match storefront.
9A.3.1 Stucco must be applied over 1/2" exterior type gypsum sheathing.
8C.2.7 Glazing Pockets: Vertical and horizontal glazing pockets shall provide
1/2" glass grippage. 91.3.2 Scratch Coat: Before hardening, cross hatch oa£clr=iri"o' ., •, �,
�4
directions. ;- . _q. r 41. ,
8C.3 • .�;T';x� = =:t� DATE:
COMPONENTS*
►• s
9A.3.3 Brown Coat: Apply approximately 3/8 "� thick. leave rough to ' r
8C.3.1 Entrances shall be medium stile design; 350 series by Kawneer Company, the finish coat.,,; _ '�' DRAWN 8Y:
Inc. with minimum 3 1/2" wide stiles and top rail and 10" bottom
rail. Botton rail sweep shall be provided on doors. 9A.3.4 Finish Coat: Apply over evenly dampened .hwn»coet: ~'Iy notes;_-• i t�IECKED BY-
than 1/8" thick. Towel to a straight, uniformsµ & #sxt r: }' r j .
finish coat moist at least 48 hours. Finish'c " olor shall �.,whitii.` {
80.3.2. Storefronts shah be Tri -Fab 451 as manufactured by Kawneer. •- ' °' °` DIYISiON
8C.3.3 Windows at office and Meat cutting Room shall be 69 -184 Series as 9A.3.5 Inspect all plastered surfaces for imperfections.• --Carr `-all , ,a� :�+� ''
manufactured by Kawneer. unsatisfactory.areaa. _`- -�« _ - -`1" "-'- _ - LOCAT �.
8C.4 EXECUTIOA SECTION 9B - ACOUSTICAL CEILINGS M.O. GUIDE PUN
8C.4.1 Inspect job conditions and do not proceed until satisfactory conditions 9B.1 GENERAL
exist.
9B.1.1 Scope: Furnish and install all acoustical ceilings indicated on the
8C.4.2. Cut and fit all material accurately with tight fitting joints. drawings and as specified herein.
Horizontal members one piece with unbroken face outside and inside.
98.1.2 Delivery and Storage of Materials: Deliver all materials in marked Cpq0,XCT may,
8C.4.3 Anchor members with fastenings of sufficient size and quantity. Allow cartons. Store materials in protected area.
for expansion and settling.
911.1.3 Qualifications: Acoustical contractor shall be approved by the
8C.4.4 Properly align and adjust entrance doors. Adjustments on doors shall manufacturer.
be made at no additional expense to Winn-Dixie.
9B.1.4 Inspection of Job Conditions: The Contractor shall not proceed -until
all unsatisfactory conditions have been corrected. Installation of DRAWING HO.
8C.4.5 Manufacturer's flashing shall be provided to allow the system to drain. n
ceilings shall constitute acceptance of conditions by acoust
8C.4.6 Tightly seal between aluminum and adjoining materials with specified ceiling contractor. _ 2
sealants. T SHEET
9B.1.5 Coordinate with electrical. contractor to ensure that_,{ �e� �. y �-
tem is properly supported to carry the electrical f''
8C.4.7 Protect aluminum in contact with masonry, steel, concrete, or other - rT Y'� Of
312499
dissimilar materials from contact by neporene gaskets or bituminous
coating.
• S
SECTION 8
8D - GLASS AND GLAZING
8A.2 PRODUCTS: The following manufacturer's material comparable to the specified
hardware shall be used unless otherwise indicated on the drawings. 8
8D.1 GENERAL
1. Locksets - Schiage, Corbin, Russwin, or Yale 8
8D.1.1 S
Scope: Furnish and install all glass and glazing work indicated on the
2. Butts - Stanley or Hager. Non - removable pins for exterior doors. d
drawings, and as specified herein.t
3. Closers - Corbin, Russwin, LCN, Norton or Yale.
•4. Door Pulls, Push Plates, Flush Bolts, Stops and Holders - Russwin, 8
8D.1.2 A
Approved manufacturers:
Corbin, Sargent, Brookline, Sargent and Greenleaf, Glynn- Johnson, or
Cipco. 1
1. Pettsburgh -Plate Glass
2. Libby- Owners -Ford
8A.3 EXECUTION: Installatin of hardware and accessory items called for under 3
3. Mississippi Glass
this section shall be installed under Section 68.
8D.1.3 L
Labels: Glass shall bear labels.
SECTION 8B STEEL DOORS AND 'FRAMES
8D.2 PRODUCTS
8B GENERAL
8D.2.1 G
Glass shall comply with Federal Specifications DD-G -451a.
8B.1.1 SCOPE: Furnish and install all steel doors and frames indicated on
the drawings and as specified herein. 8
8D.2.2 G
Glass for Storefront: Shall be a total of 1" thick, made up of 1/4"
clear glass similar to PPG clear • "Twindow" units. All glass shall be
8B.1.2 Applicable Standards: Steel doors and frames shall be manufactured t
tempered when within 4' of a door,
according to the Steel Door Institute "Recommended Specifications for
Standard Steel Doors and Frames (S.D.T. 100). 8
8D.2.3 G
Glass for Entrance Doors: 1/4" clear, tempered; polished plate.
8B.1.3 Storage: Doors -and frames shall be stored under cover on the building 8
8D.2.4 G
Glass for Meat Cutting Room, Office (and Pharmacy) if included in store
site on wood sills or on floors in a.manner that will prevent rust and d
design): 1/4" polished safety plate.
damage. V
8D.2.5 G
Glazing: Vinyl glazing gaskets with gasket Joints at top corners only.
VEPM]
8B.2 PRODUCTS S
Secure with snap -in metal molding. No exposed fastenings for any A
exterior glazing. t
A ••� ❑❑fi�
' 8B.2.1 MATERIAL: Doors and Frames shall be fabricated from steel. P
P.A.
Mirrors: .
8B.2.2 Finish: > .:.c3er mG1.3? c,:sfacZ�:. s1_431 Z =! a,t''= = .:, ctZt of
A. Toilets: Xirmi -Caioy M2114, 5
5979 N.W. 151 STR
primer. _
• B
Be Winn -Dixie Sales Area: 1/4" Polished plate glass electroplated and •
•SUITE 216
8B.2.3 Doors: a
as manufactured by Pittsburgh Plate Glass Co., or Libbey -Owens -Ford. M
M"I DES. FLA. 33
C. One -way glass installed if indicated on the Drawings. T
TEL. (305) 558 -3;
A. Clearance: Single swing doors shall have not more than 118" D
D. Solor bronze plexiglass mirror 3/16" thick laminated to 9/16" medium w
w{- 0001024, AR -60
cleared at jambs and heads, 1/4" clearance at meeting edges of pairs d
density fiberboard.
of doors, and 1/4" clearance at bottom.
8D.3 EXECUTION
Be Metal Thickness: The face panels shall be 16 gauge.
8D.3.1 I
Install all material in accordance with details or as rocoam�enaoa by �
�.
C. Internal Construction: Construction of the door shall be in t
the manufacturer.
accordance with the manufacturer's standard practice. Except exterior
8D.3.2 I
Install Sales Area mirrors as indicated on the drawings.
doors shall be solid core. 8
i
sm
8B.2.4 Frames: A. UDC continuous an ze , Q
mirrors.. Butt edges. Do not used rosettes. Use long lengths, 4'-0" O►
A. General: Frames for doors shall be .combination buck, frame and minims and 8' -0" maximum.
trim type, according to drawings.
B. Adjust tilt of mirrors to the scale optical plane with a minimum of
Be Frame Thickness: The sheet metal frames shall be 14 gauge steel distortion at joints.
for exterior frames and 16 gauge steel for interior frames. 8D.3.3 Install toilet mirrors above each lavatory 6' -0" above finish floor to 0) N
C. Frame Anchors for Wall Conditions: Provide for a mu'dmum of three top. M
anchors per jamb, 18 gauge steel. -
8D.3.4 Cleaning: At completion, the glass an plexiglass shall be cleaned of QQ
D. Floor Anchors: Provide 16 gauge anchors at the floors. all foreign matter.
CL
8B.2.5 Fire Doors and Related Frames: fire doors and frame assembly shall be SECTION BE - AUTOMATIC DOOR OPERATORS O
in accordance with the ASTM designation E- 152 -41. The label shall LL
Indicate the fire test rating for the door. SE.1 GENERAL: Furnish and install all automatic door operators indicated on the
drawings and as specified herein. W
8B.2.6 Hardware: J
8E.2 PRODUCTS >
A. Doors and Frames shall be reinforced, drilled and tapped to receive
mortised hinges, locks, latches, flush bolts and concealed door closers 8$.2.1 Automatic door operators shall be type as indicated on the drawings. 4
as required. i_ U
8E.2.2 Include all controls and equipment as required for a complete •
Be Hardware shall be field applied. installation.
C. Reinforcings and preparations shall be located as shown on Table V 8E.2.3 Finish of all aluminum shall be 140 Dark Bronze.
of the standard Door Institute "Specifications for Standard Steel Doors cc
3 EXE M IQN j
subect to individual manufacturer's 8E. D
and Frames (S.D.I. 1001, � � O
variation.
8E.3.1 Install all operators, controls and equipment, accessories, etc., in U
8B.3 EXECUTION strict accordance with manufacturer's details and instructions.
Q O
8B.3.1 Frames shall be installed plumb, rigid and in true alignment. 6E.3.2 Leave installation clean, properly adjusted, and in full and complete =
operative condition. 3:
8B.3.2 Doors shall be fastened for maxim= effectiveness and appearance. OF. IL ROLLING DOORS
8B.3.3 All exterior doors shall be weather stripped. L!J
W
8F.1.1 See Drawings for type of door and location.
0
SECTION 8C - ENTRANCES. AND STOREFRONTS 8F.1.2 Provide all locking hardware so that a padlock may be provided by (9 C>
AN
�C.1 GENERAL _ Winn -Dixie and door will be secured. C0
LU
8C.1.1 Scope: furnish and. install entrances and storefronts indicated on the 8F.1.3 Install door in strict conformance with manufacturer's printed C1
drawings-as specified herein. instructions. cc
O
8C.1.2 Shop Drawings: Submit shop-drawings to Winn- Dixie. DIVISION 9.- FINISHES ~
01)
8C.1.3 Cleaning: Clean and polish all work at the completion, as recommended SECTION 9A -LATH AMID STUCCO
by the manufacturer.
8C.1.4 Guarantees: 9A.1 GE2IERAL
9A.1.1 Scope: Furnish all labor, materials and equipment required to complete ;
A. Guarantee shall include water tightness and defects due to all LATH AM PLASH work indicated on the Drawings or as specified ;
materials or workmanship. herein.
Be Guarantee over door closers for two (2) years. Guarantee shall be .�
in writing. 9A.1.2 Delivery and Storage: Deliver all materials in their original (`�
packages, bearing name of the manufacturer, and store materials off the
floor.
8C.1.5 Approved Manufacturers: Equivalent sections of other manufacturers may %0
be substituted. contractor shall submit data as required to give 9A.1.3 Mix. Mix all stucco as recommended by the manufacturer.
evidence that the requested substitution is equivalent. Storefront'
actions shall be as manufactured b the Amarlite Corporation, Kawneer
s y 9A.1.4 Finish Texture: Shall match existing finish or shall be white with a '''•
Company, or Pittsburgh Plate Glass Company. light sand finish.
N
8C.2 MATERIALS:
ALS.
9A.2 PRODUCTS Q`
8C.2.1 Products specified as standard of quality are manufactured by Kawneer
-...._ T.... 9A.2.1 A. Main Runners: 1 -1/2" cold - rolled steel channels.
• S. l,?OSS 1lIrrlllg: J/4 w2.a- ivaaca owns v1s.a......i�_ ". ,;
8C.2.2 Extrusions: 6063 -T5 aluminum alloy meeting ASTM B221 -79a. C. Wire Hangers: No. 8 gauge.
D. Tie Wire: No. 16 gauge.
• - d h fob ' 4 d from alvanized steel h
8C.2.3 Aluminum Sheet: 5005 -H34 aluminum alloy meeting ASTR B209 -80, minimum E. Aetal Lath: Diamon mes rice e g •
0.050" thickness. F. Casing Beads: Square end, sized to full stucco thickness.
U. *2WLPa M.LVU UV.LU% -0i 0AK-VFQ w Goal oU-- ••-•.Aw..._�, sa_
8C.2.4 Fasteners: All fastening devices shall be stainless steel; countersink 75 at 10' -0" O.C. if not indicated on drawings.
exposed fasteners; match entrances and storefronts in color. All
fasteners shall be tamper proof. 9A.2.2 A. Portland Cement: Type I, non staining, ASTK C -150. DRAWING TITLE
Be Lime: ASTM C -206, Type S, Double Hydrated. c
J
8C.2.5 Finish: All exposed aluminum surfaces including brake metal shall have C. Masonry Cement: ASTM C -91, Type II. SPEC l
architectural Class 1 anodic coating with integral color conforming to . D. Sand: Clean, well- graded from coarse to fine.
Aluminum Allocation standard AA -M12 C22 A42/44. Color shall be #40 E. Water: Potable
Dark Bronze. F. Finish Coat: Factory pre-mixed white stucco with light sand finish.
8C.2.6 Storefront Sealant: Non - skinning type meeting NAAMM standards 5C -1.1. 9A.3 APPLICATION OF STUCCO
color to match storefront.
9A.3.1 Stucco must be applied over 1/2" exterior type gypsum sheathing.
8C.2.7 Glazing Pockets: Vertical and horizontal glazing pockets shall provide
1/2" glass grippage. 91.3.2 Scratch Coat: Before hardening, cross hatch oa£clr=iri"o' ., •, �,
�4
directions. ;- . _q. r 41. ,
8C.3 • .�;T';x� = =:t� DATE:
COMPONENTS*
►• s
9A.3.3 Brown Coat: Apply approximately 3/8 "� thick. leave rough to ' r
8C.3.1 Entrances shall be medium stile design; 350 series by Kawneer Company, the finish coat.,,; _ '�' DRAWN 8Y:
Inc. with minimum 3 1/2" wide stiles and top rail and 10" bottom
rail. Botton rail sweep shall be provided on doors. 9A.3.4 Finish Coat: Apply over evenly dampened .hwn»coet: ~'Iy notes;_-• i t�IECKED BY-
than 1/8" thick. Towel to a straight, uniformsµ & #sxt r: }' r j .
finish coat moist at least 48 hours. Finish'c " olor shall �.,whitii.` {
80.3.2. Storefronts shah be Tri -Fab 451 as manufactured by Kawneer. •- ' °' °` DIYISiON
8C.3.3 Windows at office and Meat cutting Room shall be 69 -184 Series as 9A.3.5 Inspect all plastered surfaces for imperfections.• --Carr `-all , ,a� :�+� ''
manufactured by Kawneer. unsatisfactory.areaa. _`- -�« _ - -`1" "-'- _ - LOCAT �.
8C.4 EXECUTIOA SECTION 9B - ACOUSTICAL CEILINGS M.O. GUIDE PUN
8C.4.1 Inspect job conditions and do not proceed until satisfactory conditions 9B.1 GENERAL
exist.
9B.1.1 Scope: Furnish and install all acoustical ceilings indicated on the
8C.4.2. Cut and fit all material accurately with tight fitting joints. drawings and as specified herein.
Horizontal members one piece with unbroken face outside and inside.
98.1.2 Delivery and Storage of Materials: Deliver all materials in marked Cpq0,XCT may,
8C.4.3 Anchor members with fastenings of sufficient size and quantity. Allow cartons. Store materials in protected area.
for expansion and settling.
911.1.3 Qualifications: Acoustical contractor shall be approved by the
8C.4.4 Properly align and adjust entrance doors. Adjustments on doors shall manufacturer.
be made at no additional expense to Winn-Dixie.
9B.1.4 Inspection of Job Conditions: The Contractor shall not proceed -until
all unsatisfactory conditions have been corrected. Installation of DRAWING HO.
8C.4.5 Manufacturer's flashing shall be provided to allow the system to drain. n
ceilings shall constitute acceptance of conditions by acoust
8C.4.6 Tightly seal between aluminum and adjoining materials with specified ceiling contractor. _ 2
sealants. T SHEET
9B.1.5 Coordinate with electrical. contractor to ensure that_,{ �e� �. y �-
tem is properly supported to carry the electrical f''
8C.4.7 Protect aluminum in contact with masonry, steel, concrete, or other - rT Y'� Of
312499
312499